Sealey AK4564D - Manual

❐ WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
✓
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to this product.
✓
Maintain the pump station in good condition (use an authorised service agent).
✓ Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the warranty.
✓
Use only to dispense lubricants up to SAE 150 viscosity and antifreeze liquids.
✓
Ensure safety eye protection and protective clothing are worn when using this product.
✓ Keep the work area clean, uncluttered and ensure there is adequate lighting.
✓
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
✓ Keep children and unauthorised persons away from the working area.
✓
After use, drain any fluids from the equipment before storage.
✓
Dispose of waste liquids in accordance with local authority regulations.
✓ Disconnect air pressure from equipment when not in use.
✗
DO NOT exceed the maximum working pressure of 1500psi.
✗
DO NOT point the nozzle at people or animals.
✗
DO NOT use the equipment near open flames.
✗
DO NOT smoke whilst using this equipment.
✗ DO NOT use to extract corrosive fluids.
✗
DO NOT dismantle, tamper with or adapt the gun for any purpose other than for which it is designed.
✗
DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
✓ Keep the gun and nozzle clean and store in a safe dry, childproof location.
❐ WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment. All liquids must be disposed of according to
local authority regulations.
InStRUctIonS FoR:
OIl hOse eND GuN
Model no:
AK4564D
1. sAFeTY INsTRuCTIONs
2. INTRODuCTION
3. AssemblY
4. OpeRATION
IMPORTANT: pleAse ReAD These INsTRuCTIONs CAReFullY. NOTe The sAFe OpeRATIONAl ReQuIRemeNTs,
WARNINGs AND CAuTIONs. use ThIs pRODuCT CORReCTlY AND WITh CARe FOR The puRpOse FOR WhICh IT Is
INTeNDeD. FAIluRe TO DO sO mAY CAuse DAmAGe OR peRsONAl INJuRY AND WIll INVAlIDATe The WARRANTY.
pleAse ReTAIN These INsTRuCTIONs FOR FuTuRe use.
thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance
if these instructions are carefully followed and the product is correctly maintained.
AK4564D Issue no: 1 - 14/11/08
Robust oil dispensing gun incorporating manual shut off. Fitted with rigid
extension, handle lock and non-drip nozzle.
*Please note that this gun is not approved for resale of oil.
3.1 Attach the nozzle assembly to the gun.
3.2 Insert the filter into the inlet connection and then attach the supply hose.
Note: DO NOT overtighten the inlet swivel connection or damage may result.
Model: AK4564D
Maximum Flow Rate: 35ltr/min
Maximum output Pressure: 1500psi
Inlet: 1/2”BSP
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImpORTANT: no liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORmATION: call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
01284 757500
[email protected]
www.sealey.co.uk
01284 703534
sole u.K. Distributor
sealey Group
Bury St. Edmunds
Suffolk.
Web
fig.1
4.1 Open the nozzle valve (fig.1).
4.2 Press trigger to dispense liquid, the trigger can be locked open for
long periods of dispensing using the clip.
❐ WARNING! DO NOT leave the gun dispensing unattended.
4.3 Release the trigger to stop dispensing.
4.4 close the nozzle valve.