Sealey CM4 User Manual
Corner movers 4pc, Instructions for, Model no
InstructIons for:
CORNER MOVERS 4PC
MoDEL no:
CM4
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1 GENERAL SAFETY
WARNING! Ensure Health & Safety, and local authority regulations
are adhered to when assembling and using this corner moving
system.
Keep the general area where used clean, uncluttered and ensure
there is adequate lighting.
WARNING! use on a level and solid surface such as concrete.
DO NOT use the corner moving system
for any purpose other
than that for which it is designed.
Ensure that the corner movers are properly assembled before
loading.
DO NOT overload the corner movers, 37.5 kgs per corner mover.
We recommend two operators for
heavier loads.
Always push the loaded corner movers as near to bottom of the
load as sensibly practical to avoid tipping hazard.
Always use all 4 corner movers to transport the load.
DO NOT let go of the load whilst in motion.
3. CONTENTS
2. INTRODUCTION
carefully unpack the product and check the contents against the list
below. should any items be missing or damaged make immediate
contact with your sealey dealer.
Part Description . . . . . . . . . . . . QTY
swivel castors: . . . . . . . . . . . . . . 12
corner platform: . . . . . . . . . . . . . . .4
rubber pad: . . . . . . . . . . . . . . . . . .4
Plain washer Ø12: . . . . . . . . . . . . 12
4. ASSEMbLY
4.1 Place the 12 plain washers on to the 12 castor studs (fig.1).
4.2 Wind the castor studs into the 3 captive nuts in the corner
platforms (fig.2). Ensure the castors are tight using "plumbers"
pliers or similar thin nosed grips on to the swivel ball race outer
journal (fig.1).
4.3 Position the rubber pads as in fig.3.
fig.1
Heavy-duty corner movers manufactured from high quality steel with
a maximum load weight of 150kg. Ideal for moving awkward
rectangular loads and provides increased mobility in locations where
normal material handling equipment cannot be used. Each corner
mover is fitted with three free moving castor wheels for easy
manoeuvrability and fitted with a rubber covered load area to help
secure loads. Ideal for moving items such as cabinets, desks and
much more. sold in sets of four.
Original Language Version
cM4 Issue: 1- 14/03/14
© Jack sealey Limited
Ball race journal
Plain washer
continuously welded
corner platforms
fig.4
fig.2
fig.5
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
6. MAINTENANCE
6.1 check swivel castor integrity regularly. see 4.2.
6.2 Keep clean with moistened cloth and mild detergent.
6.3 smear ball journals with grease if required.
5. OPERATION
5.1 Working on your own (two operators on heavy or tall loads), pivot
the load and with your foot roll the wheeled corner platforms
beneath as shown in fig.4. nest fully and relocate (fig.5).
5.2 remove as loaded and with your feet steady the corner platforms.
(two operators on heavy or tall loads)
fig.3
Position of self
adhesive pads
recycle unwanted materials instead of disposing of them
as waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a
manner which is compatible with the environment
When the product is no longer required, it must be disposed
of in an environmentally protective way