Sealey CST978 User Manual
Cst978.v2, Sack truck models, Fig.2
1. SAFETY INSTRUCTIONS
2. SPECIFICATION
Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
Obtain additional support for large or wide loads to prevent tipping.
Do Not overload the truck - see Specification.
Do Not leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
Do Not use truck on uneven ground and do not run over curbs or steps - use a ramp.
Do Not allow others to ride on the truck.
Do Not use the truck if any part is damaged, paying particular attention to the wheels.
3. ASSEMBLY
Model No. . . . . . . . . . . . . . . . . . . . . CST978.V2
Max. Load. . . . . . . . . . . . . . . . . . . . . . . . . .250kg
Wheel Diameter . . . . . . . . . . . . . . . . . . . .250mm
Wheel Thickness . . . . . . . . . . . . . . . . . . . .88mm
Height . . . . . . . . . . . . . . . . . . . . . . . . . .1450mm
Overall Width . . . . . . . . . . . . . . . . . . . . . .550mm
Platform Depth . . . . . . . . . . . . . . . . . . . . .225mm
Fig.2
3.1
Wheels. Ensure each axle is clean from dust and dirt to allow free movement
of the wheel. You will need to slide the axle through the frame bushes first.
3.1.1 Slide the wheel (1.2) onto the axle (1.1), followed by the washer (1.3) and
complete by pushing the split pin (1.4) through the hole in the end of the axle
and bending over to retain.
3.1.2 Repeat for the other side.
3.2
Castor Wheels.
3.2.1 Bolt the two castor wheels to the flat cross member at the other end of the
frame (see Fig.2&3).
3.2.2 Insert the threaded stub through the hole, place the flat washer provided over
the threaded stub followed by the split spring washer and retaining nut. Tighten
both nuts.
3.3
HANDLE. (To assemble in sack truck configuration)
3.3.1 Fully insert the loop handle into the main frame tubes as shown.
3.3.2 Retain in place by inserting an ‘R’ clip through each tube as shown in Fig.2.
Ensure that the clip is on the back of the frame away from the loading surface.
It may be necessary to lift the handle very slightly to get the holes in the
handle tube to align with the holes in the frame tubes.
3.4
HANDLE. (To assemble as a flat bed truck configuration)
3.4.1 Firstly remove the ‘R’ clips from the main frame tubes and withdraw the loop
handle.
3.4.2 Lay the frame horizontal and insert the loop handle into the short length tubes
above the castors as shown in Fig.3.
3.4.3 Retain in place by inserting an ‘R’ clip through each tube as shown in Fig.3. It
may be necessary to lift the handle very slightly to get the holes in the handle
tube to align with the holes in the short length tubes.
InSTRucTIOnS FOR:
SACK TRUCK
Models:
CST978.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
We b
Fig.1
Tubular steel framework with heavy-duty pneumatic wheels. use as a traditional sack truck or in
a horizontal position. Quick and easy conversion between different configurations.
Parts support is available for this product. To obtain a parts listing, please email
[email protected] or phone 01284 757500.
Fig.3
cST978.V2 Issue: 1- 07/01/09