Sealey STR002 User Manual
Str002, Fig.1, Safety instructions
InstructIon MAnuAL for:
mobile TYRe RACKiNG SYSTem 200KG
CAPACiTY PeR leVel
MoDEL no:
STR002
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFeTY iNSTRUCTioNS
IMPORTANT: PleASe ReAD THeSe iNSTRUCTioNS CAReFUllY. NoTe THe SAFe oPeRATioNAl ReQUiRemeNTS, WARNiNGS & CAUTioNS.
USe THe PRoDUCT CoRReCTlY AND WiTH CARe FoR THe PURPoSe FoR WHiCH iT iS iNTeNDeD. FAilURe To Do So mAY CAUSe
DAmAGe oR PeRSoNAl iNJURY, AND Will iNVAliDATe THe WARRANTY. PleASe KeeP iNSTRUCTioNS SAFe FoR FUTURe USe.
1.1 GeNeRAl SAFeTY
WARNiNG! Ensure Health & Safety, and local authority regulations
are adhered to when assembling and using this racking system.
Locate the racking in a suitable area where it will not be an
obstruction.
Keep the general area clean, uncluttered and ensure there is
adequate lighting.
WARNiNG! use the racking on a level and solid surface such
as concrete.
Keep children and unauthorised persons away from the storage
area.
Do NoT use the racking
for any purpose other than that for
which they are designed.
Do NoT get the racking wet or use in damp or wet locations or
areas where there is condensation.
Do NoT clean the cross beams with any solvents which may
damage the coated surface.
Do NoT overload the racking.
Do NoT allow others to ride on the racking.
Do NoT push loaded racking over edges, rough surfaces etc. as
the whole unit may overturn.
Ensure that the racking is properly assembled before loading
with heavy tyres.
Maximum load for each level is 200kg. Load must be evenly
distributed.
Place heavier items on the lower racks.
Maintain correct balance and footing when moving the racking
and ensure that the floor surface is not slippery.
Where possible heavier items should be evenly distributed across
the racks.
3. CoNTeNTS
2. iNTRoDUCTioN
carefully unpack the product and check the contents (fig.1)
against the list below. should any items be missing or damaged,
immediately contact your sealey dealer.
Part Description............................................................Quantity
A upright .........................................................................................4
b Horizontal Brace ..........................................................................8
C Diagonal Brace ............................................................................4
D spacer .........................................................................................4
e castor* ........................................................................................4
F Bolt M6 x 50mm ........................................................................14
G nut M6 .......................................................................................26
H safety Bolt M6 x 20mm .............................................................12
i cross Beam.................................................................................6
J Bolt M10 x 20mm ......................................................................16
K nut M10 and spring Washer .....................................................16
* 2 x swivel castors and 2 x fixed castors
4. ASSemblY
Warning! Before assembly and use ensure you have read,
understood and apply Section 1 safety instructions.
4.1 It is recommended that this tyre racking system be assembled by
two people. When installing the cross beams it is advisable to
use a rubber mallet. Do not use a hard faced hammer as this will
damage the surface finish of the cross beams. Make sure that all
the clips lock in place securely and safety bolts are fitted before
using the unit. Do not use any parts that are damaged and/or
distorted as these may assemble incorrectly and result in an
installation that is unsafe and which may cause injury or damage
when the shelves are loaded.
three level mobile tyre rack system helps keep working area clear.
unit is on wheels for easy manoeuvrability when needing to take the
tyres to point of work, ideal for use track side. steel construction with
a powder coated finish giving anti-corrosion resistance.
Height: 1700mm
Width: 915mm
Depth: 455mm
maximum Capacity: 600kg (200kg/level)
str002 IssuE 1 05/08/11
Original Language Version
fig.1