Sealey TPS22 - Manual

InstructIons for:
Mobile bin storage systeMs
MoDEL no's:
tPs22, tPs36
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. saFety instrUCtions
IMPORTANT: Please reaD tHese instrUCtions CareFUlly. note tHe saFe oPerational reQUireMents, Warnings &
CaUtions. Use tHe ProDUCt CorreCtly anD WitH Care For tHe PUrPose For WHiCH it is intenDeD. FailUre to Do so May
CaUse DaMage or Personal inJUry, anD Will inValiDate tHe Warranty. Please KeeP instrUCtions saFe For FUtUre Use.
1.1 general saFety

Warning! Ensure Health & Safety, and local authority regulations
are adhered to when assembling and using this storage system.

Locate storage system in a suitable area where it will not be an
obstruction.
 Keep the general area clean, uncluttered and ensure there is
adequate lighting.

Warning! Erect storage system on a level and solid surface
such as concrete.

Keep children and unauthorised persons away from the storage
area.

Do not use the storage system for any purpose other than that
for which it is designed.
 Do not site the storage system out of doors.

Do not get the storage system wet or use in damp or wet
locations or areas where there is condensation.

Do not clean the shelf supports with any solvents which may
damage the coated surface.
 Ensure that the storage system is properly assembled before
loading with heavy items.

Load for each shelf must be evenly distributed.

Place heavier items on the lower shelves of the storage system.

Always push the storage system from the sides, pushing from
the front or back creates a tipping hazard.
3. Contents
2. introDUCtion
carefully unpack the product and check the contents against the list
below. should any items be missing or damaged make immediate
contact with your sealey dealer.
Part Description . . . . . . . . . . . tPs22. . . . . tPs36
castors (2 Locking) . . . . . . . . . . . . 4 . . . . . . . . . 4
uprights . . . . . . . . . . . . . . . . . . . . . 4 . . . . . . . . . 4
Beam (Double tab) . . . . . . . . . . . . 4 . . . . . . . . . 4
side Brace (Double tab) . . . . . . . . 4 . . . . . . . . . 4
shelf Beam (single tab) . . . . . . . . 8 . . . . . . . . . 16
side centre Brace (single tab) . . . 2 . . . . . . . . . 2
Wire shelf (Large Bins) . . . . . . . . . 1 . . . . . . . . . 3
Wire shelf (Medium Bins) . . . . . . . 1 . . . . . . . . . 3
Wire shelf (small Bins) . . . . . . . . . 3 . . . . . . . . . 3
Wire shelf (top) . . . . . . . . . . . . . . . 1 . . . . . . . . . 1
Large Bins . . . . . . . . . . . . . . . . . . . 3 . . . . . . . . . 9
Medium Bins. . . . . . . . . . . . . . . . . . 4 . . . . . . . . . 12
small Bins . . . . . . . . . . . . . . . . . . . 15 . . . . . . . . 15
4. asseMbly
4.1 take the four uprights and insert the four castors into the bottom
of each. see fig.1.
Ensure the castors are fully seated.
fig.1
Powder coated steel racks with robust composite storage bins evenly
spread across multiple shelves. Mounted on heavy-duty castors (two
lockable) for mobility. unit can hold up to a maximum weight of
60kg - 150kg (Model dependant) evenly spread across the bins.
optional fixing kit available allowing multiple units to be joined
together - order Model no. tPsJK.
fig.2
4.2 Assemble the front and back frames.
4.2.1 take two of the uprights with locking castors and insert long
beam between the two uprights at the top and bottom. see
fig.2. Ensure the beams are the correct way up (fig.2A/B) and
seated correctly, use a soft faced mallet to tap the beams
home.
4.2.2 repeat process for the other two uprights using the
non-locking castors.
Original Language Version tPs22, tPs36 Issue: 2 - 28/06/12 © Jack sealey Limited