Sealey TPS47 User Manual
Tps47, Storage system with 47 bins, Instructions for
01284 757500
01284 703534
www.sealey.co.uk
INSTRUCTIONS FOR:
STORAGE SYSTEM WITH 47 BINS
MODEL No.
TPS47
1. SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this rack.
Locate rack in a suitable work area.
Keep the work area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Use rack on level and solid ground, preferably
concrete.
Keep the rack clean and tidy in accordance with good workshop
practice.
DO NOT use the rack
for any purpose other than that for which it
is designed.
Keep children and unauthorised persons away from the work area.
DO NOT climb on racking.
2. SPECIFICATION
3. ASSEMBLY
Floor standing, powder coated steel racking with two sizes of
plastic storage bins.
32 Small Bins ............................................... (110 x 160 x 75mm)
15 Large Bins ............................................. (150 x 235 x 125mm)
Rack Height: ....................................................................1145mm
Rack Width: ...................................................................... 940mm
Rack Depth: ..................................................................... 285mm
Weight: ..................................................................................22kg
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
3.1. Position the LH upright (1) and the RH upright (2) onto the
upstanding spigots on the base (3) ensuring that the attached
brackets (7) are facing inwards. On each upright it is the end
with no internal fixings which should be dropped over each spigot.
Secure each upright with two 14mm M4 bolts with a lock washer
under the head of each bolt.
3.2. Attach a brace (4) between each upright (1 & 2) and the base
(3) and secure each with two 14mm M4 bolts and lock washers.
3.3. Place the top (5) onto the two uprights ensuring that the uprights
go into the metal sockets in the back inside corners of the top.
Secure each upright with two 14mm M4 bolts and lock washers.
3.4. Bolt the seven cross braces (7) to the brackets on the inside
faces of the two uprights (1 & 2). Position each cross brace onto
the front faces of the adjacent brackets ensuring that the centre
support fixing hole is offset to the right. Fix each cross brace with
two 8mm M4 nuts and bolts at each end.
3.5. Attach the Centre Support (8) to the back of the cross braces
using
14mm M4 bolts with a lock washer under the head of each
bolt.
3.6. Attach the storage bins to the cross braces by pushing the rear
lip on each bin over the top front edge of the cross braces.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
© Jack Sealey Limited
Original Language Version
Issue No:3(L) 06/03/14
TPS47 Issue No: 3(L) - 06/03/14