Sealey AP28102 - Manual

INSTRUCTIONS FOR
ADD-ON RETRO MID-BOX 2 DRAWER
MODEL NO:
AP28102
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
R WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this product.
R WARNING! Use caution when handling and assembling the metal components. The metal may have sharp edges or corners, the use of
protective gloves is recommended.
 DO NOT open more than one drawer at a time.
 DO NOT step on the drawers.
 DO NOT let children play with the roll cab or top chest.
 Ensure all drawers are fully closed and the self locking catch is activated, before moving the toolbox.
 Secure the brakes when rollcab is in the desired position.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
 Keep the mounting frame clean and tidy in accordance with good workshop practice.
 DO NOT use in damp work areas.
R WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
2. INTRODUCTION
Retro style mid-box featuring 2 drawers with ball bearing slides. Lift latch drawer pulls preventing inadvertent opening. Drawers are fitted with
drawer liners and lock on one key turn. For use with Model No. AP28104 (Topchest) and Model No. AP28204 (Rollcab) to make a complete
retro style stack unit. Purchase separately to enhance previously purchased Model No. AP28COMBO Rollcab and Topchest Combo.
3. SPECIFICATION
Model no: ............................................................... AP28102
Dimensions (W x D x H): .........................712 x 457 x 270mm
Medium drawer (x2): .................................570 x 400 x 60mm
4. ASSEMBLY
4.1. Connection to Top Chest and Rollcab see fig.4
4.1.1. Place the mid-box onto the roll cab. Fit the connectors into the
rectangular holes and fasten with the screws provided.
4.1.2. Place the top chest onto top of the mid-box and fit the connectors
into the top chest and fasten with the screws provided.
5. OPERATION
5.1. To open drawers
5.1.1. To open: lift the drawer front whilst pulling it out (fig.1).
5.1.2. To close: shut the drawer firmly until the latch engages.
5.1.3. If the drawer does not latch, the hook (fig.1) may be misaligned or binding. Bend the hook gently until it is parallel to the drawer edge
and engages when closed.
5.2. To remove drawers
5.2.1. Pull drawer out almost fully.
5.2.2. Locate the black locking levers (figs. 2 & 3).
5.2.3. Facing the drawer; lift one lever up (fig.2), and push the other lever down (fig.3).
5.2.4. With both levers deployed, the drawer can be pulled out from the slides.
5.3. T o replace drawers
5.3.1. Extend the drawer runners from the cabinet.
5.3.2. Engage the slides on either side of the drawer carefully into the runners.
5.3.3. Push the drawer closed squarely until the drawer is closed fully, engaging the locking levers as it goes.
Refer to
Instruction
manual
AP28102| Issue 1 05/05/15 Original Language Version © Jack Sealey Limited
fig.1