Sealey PTB91508 - Manual

INSTRUCTIONS FOR:
TOPCHEST 8 DRAWER 915MM HEAVY-DUTY/
ROLLCAB 6 DRAWER 930MM HEAVY-DUTY
MODEL No' s: PTB91508, PTB93006
1.1. GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
 Locate the units in a suitable work area.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
 WARNING! Use the units on level and solid ground, preferably concrete.
 Keep the units clean and tidy in accordance with good workshop practice.
 Keep children and unauthorised persons away from the work area.
 DO NOT use these units for any purpose other than that for which they are designed.
 DO NOT use the units outdoors.
 DO NOT place the units in a damp or wet location or an area where there is condensation.
 DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.
 DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
moving.

DO NOT step on the drawers.
• Heavy-duty all welded steel construction for strength and durability. • Heavy-duty all welded steel construction for strength and durability.
• Textured powder coat fi nish which is solvent and rust resistant.
• Textured powder coat fi nish which is solvent and rust resistant.
• Ball bearing drawer runners provide superior performance and carry heavier loads, double sets on large drawers.
• Ball bearing drawer runners provide superior performance and carry heavier loads, double sets on large drawers.
• All drawers have full width sand blasted aluminium lift latch drawer pulls, making easy access and prevention of inadvertent opening when box is being
• All drawers have full width sand blasted aluminium lift latch drawer pulls, making easy access and prevention of inadvertent opening when box is being
moved.
moved.
• Heavy-duty Ø125mm Mag style castors, 2 swivel with toe brakes and 2 fi xed.
• Heavy-duty Ø125mm Mag style castors, 2 swivel with toe brakes and 2 fi xed.
• Heavy-duty exterior handles on chest and cabinets.
• Heavy-duty exterior handles on chest and cabinets.
• Topchests feature gas struts on lids for easy opening.
• Topchests feature gas struts on lids for easy opening.
• Non-slip drawer liners supplied for all drawers.
• Non-slip drawer liners supplied for all drawers.
• Rollcabs supplied with 12mm PVC coated MDF worktop.
• Rollcabs supplied with 12mm PVC coated MDF worktop.
• Integral locking system locks all drawers in each unit with the turn of 1 key.
• Integral locking system locks all drawers in each unit with the turn of 1 key.
• All supplied with 2 keys.
• All supplied with 2 keys.
• Manufactured to the highest levels of construction to withstand the toughest of workshop/garage conditions.
• Manufactured to the highest levels of construction to withstand the toughest of workshop/garage conditions.
Model No: PTB91508 Model No: PTB93006
Overall Size (WxDxH) (mm): 915 x 450 x 565 Overall Size (WxDxH) (mm): 930 x 460 x 1050
Medium 1/2 Drawer (x6): 385 x 385 x 58 Medium Drawer (x3): 825 x 385 x 58
Medium Drawer (x2): 825 x 385 x 58 Large Drawer (x2): 825 x 385 x 135
X-Large Drawer (x1): 825 x 385 x 210
Original Language Version © Jack Sealey Limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
4. ASSEMBLY
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. Install Handle (refer to fi g.1).
4.2.1. Position the holes and attach with the bolts provided. Tighten securely.
Fig.1 Fig.2
4.3. Install Wheels (Rollcabs) (Refer to fi g.2).
4.3.1. Carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. Tighten securely.
4.3.3. Install the fi xed wheels on the opposite end to the handle.
4.4.
Remove Drawers (Refer to fi g.3).
4.1.1. Pull drawer out until it is almost fully extended. Push up one black release lever, while pulling down the other hand black release lever.
PTB91508, PTB93006 | Issue: 2S - 23/12/14