Sealey MC365 - Manual

INSTRUCTIONS FOR
365KG HYDRAULIC MOTORCYCLE LIFT
MODEL NO:
MC365.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
R WARNING! THIS LIFT IS ONLY SUITABLE FOR MOTORCYCLES WHICH HAVE A CENTRE STAND.
R WARNING! Ensure the bike is adequately strapped onto the platform before operating.
 Maintain the lift in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up hydraulic unit.
 Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike. DO NOT
operate the lift on tarmacadam, as the surface may be unstable.
 Keep the lift clean for best and safest performance.
 The maximum bike weight is 365kg. DO NOT exceed this rated capacity.
 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
 Maintain correct balance and footing, do not over reach. Ensure the floor is not slippery and wear non-slip shoes.
 Ensure the bike is adequately secured to the lifting platform with appropriate straps.
 Before lifting check that there are no overhead obstructions.
 When platform has been raised to the working height ensure the locking bar is engaged to prevent accidental lowering.
 Keep children and unauthorised persons away from the work area.
 The lowering speed will vary according to the weight of the load and the amount by which the release pedal is depressed.
 DO NOT use the lift for a task it is not designed to perform.
 DO NOT operate the lift if damaged.
 DO NOT exceed the rated capacity of the lift.
 DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT allow untrained persons to operate the lift.
 DO NOT attempt to transport a load on the lift. The lift must only be used in a static position for raising and lowering loads.
 DO NOT make any modifications to the lift and DO NOT adjust or tamper with the safety valve.
 Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
 Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
2. INTRODUCTION
All steel construction with foot operated, integral hydraulic pump and ram assembly. Fitted with safety lock device to fix platform at three
Working heights of 760mm, 640mm and 500mm and to prevent accidental lowering. Suitable only for motorcycles with a centre stand. Support
platform fitted with full width loading ramp. Base assembly fitted with transport wheels and lock downs to prevent lift from moving during use.
3. SPECIFICATION
Model no: ............................................................. MC365.V2
Capacity: ...................................................................... 365kg
Minimum height: ......................................................... 220mm
Maximum height: ........................................................ 760mm
Width: ......................................................................... 480mm
Length: ..................................................................... 2215mm
Max. load length: ...................................................... 1350mm
4. CONTENTS
Unpack the lift and check contents with list below. Should there be any damaged or missing parts contact your supplier immediately.
• Main Assembly • Sliding Plate • Leading Plate • Vice
• Lifting Pedal • Release Pedal • Bolts, Washers, Nuts, Cotter Pins
No reaching in Refer to
Instruction
Manual
MC365.V2 | Issue 3(I) 08/05/15 Original Language Version © Jack Sealey Limited