Euro-Pro VPW43 - Manual (Page 5)

Cleaning the Nozzles: If you notice that
the output pressure fluctuates, you may
have to clean the nozzles. Turn the unit
"Off". Unplug from electric outlet and
disconnect the water supply. Remove
the lances, trigger gun and hose from
unit. Take the small metal pin provided
and insert into the nozzle end to
remove any obstructions. (Fig. 15)
Fig. 15
This will occur more frequently if your
water supply is very hard.
Storing Your Pressure Washer
When you have finished using your
pressure washer, follow these steps for
safe storage:
1. Turn the pressure washer to the
"Off" position.
2. Turn off the water supply.
3. Before disconnecting the high
pressure hose connection, point the
trigger gun in a safe direction away
from you and discharge the high
pressure water. Disconnect the high
pressure hose from the pressure
washer and trigger gun.
4. Disconnect garden hose from
pressure washer.
5. Remove excess water from the
pump by tipping the unit on both
sides to drain any remaining water
from the water intake and outlet
fittings.
6. Drain detergent applicator bottle and
flush with clean water.
7. Wipe away any remaining water on
all parts and fittings.
8. Engage the trigger gun safety lock.
9. Store the unit and accessories in a
room above 32°F.
Winterizing & Long Term Storage
1. Disconnect all water connections.
2. Turn the pressure washer on for a
few seconds, until any remaining
water in the pump exits.
3. Turn the unit off immediately.
4. Store the pressure washer, parts
and accessories in an area with a
temperature above 32°F.
Fig. 12
Fig. 11
This high pressure washer is suitable for
non-professional use. The working
temperature must range between 40°F
and 120 °F. The machine is supplied with
a trigger gun, equipped with a trigger
handle to offer a comfortable working
position.
The high pressure washer is suitable for
washing with cold water only. The water
that you use for the pressure washer
must not be dirty, sandy or contain any
corrosive chemical products.
The pressure washer may be used to
wash shutters, doors, tiles, cars, decks,
campers, etc., where high water pressure
is necessary to remove dirt.
With the detergent applicator bottle, the
pressure washer can be used to apply a
thick coating of aerated detergent to the
areas being cleaned .
When using the pressure washer we
recommend the use of personal safety
items to reduce the risk of accidental
injury.
Suitable Use of Your Pressure
Washer
• Place the pressure washer in a safe
area and on a horizontal surface.
• When using the pressure washer,
hold the trigger gun firmly with one
hand on the handle and the other on
the lance. (Fig. 1)
Correct Use of the Pressure
Washer
Fig. 1
• NEVER point the water jet at electric
wiring, at the pump unit, or at any
person or animal.
1. Carefully take all the trolley parts and
place together on a flat, stable
surface.
2. Insert the two (2) legs into the
support brackets on the unit and
secure with two (2) of the 1/2-inch #8
Phillips screws provided. (Fig. 2)
Assembling the Pressure Washer
Trolley
Fig. 2
3. Insert the handle into the handle
bracket and secure with two (2) of the
1-inch #8 Phillips screws provided.
(Fig. 3)
Fig. 3
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
Using the High Pressure Lance
The high pressure lance may be used
alone or with the detergent applicator
bottle.
Add detergent to the bottle and then
attach the detergent applicator bottle to
the high pressure lance, just push it on
the end of the high pressure lance.
(Fig. 11 & 12) To remove the detergent
applicator bottle, lift the tab on the top
of the connector and pull off.
Using the Brush With the Trigger
Gun
The brush is used with the trigger gun.
Push the brush onto the trigger gun
nozzle and turn clockwise to lock as
you would for the lances. (Fig. 13) The
brush may be used for washing cars,
boats, windows and other similar items.
The brush operate at open orifice
pressure so that they will not direct a
stream of water.
Fig. 13
Unpacking Your Pressure Washer
After you open the package, check to
make sure that all the parts are in the box
as pre parts that illustrated on page 3 of
this guide. Due to transport and packing
restraints, some accessories may be
supplied unassembled; in this case follow
the assembly instructions in this manual.
If you have any questions, call EURO-
PRO Operating LLC customer service at
1 (800) 798-7398. Keep all small and
potentially harmful parts of the package
(plastic bags, foamed polystyrene, nails,
etc.) out of the reach of children.
Lubrication: The pressure washer is
supplied with a closed lubrication
system, so no addition of oil is needed.
Checking the Water Intake Filter: The
water intake filter is located inside the
water intake connector. (Fig. 14).
Remove periodically and inspect for
any deposits that might accumulate
there.
Fig. 14
Hose Connector
Water Intake
Maintenance & Cleaning
7 4