EarthQuake 3365PSCE - Manual (Page 7)

OPERATOR INSTRUCTIONS ANd PARTS
Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE
Page 7
GetEarthquake.com
800-45-6007
UNPACkING ANd ASSEMBLY
UNPACk TILLER & ASSEMBLE
1. Open top of carton and remove handlebar assembly.
2. Find parts packet. Parts packet for 3365/3365B/3365K/3365CE
contains:
6- 5/16-18 x 1-3/4” bolts
6- 5/16” spring lockwashers
2- hand knobs
4- locknuts
2- 1/2” push nuts
1- detent pin
Parts packet for 3365PS/3365KPS/R3365H/3365PSCE con-
tains:
2- 3/8-16 x 1” bolts
2- 3/8-16 biway locknuts
2- 5/16-18 x 1” bolts
4- 5/16-18 x 1-3/4” bolts
6- 5/16” spring lockwashers
2- hand knobs
4- 5/16” locknuts
2- 1/2” push nuts
1- detent pin
3. Cut open end of carton and remove machine:
a. Install wheels on each end of axle; tap on push nuts with a
hammer.
b. Assemble tines to unit, inside tines first. Sharp edge of tine
will be away from operator at top, or face down at front of
machine.
c. Outside tines have two positions- wide 21” and narrow 16”.
For narrow width, assemble with short side of tine holder pipe
towards center of machine.
d. For wide width, move the left tine to the right side and right
tine to the left side. Assemble with the long half of tine pipe
towards machine.
e. Slide the top handle of handlebar over the lower loop. Put
5/16-18 x 1-3/4” bolts through both holes from inside out;
put on 5/16” spring lockwashers and tighten with hand
knobs. Models 3365PS, 3365KPS, and R3365H will use
3/8-16 x 1” bolts with nuts and 5/16-18 x 1”
bolts with hand knobs. See parts explosion on page 19.
f. Check upper and lower jam nuts for tightness. See page 9,
Belt Tension Adjustment.
g. Add and check engine oil.
INSTALL dEPTh REGULATOR LEvER
1. Install the depth regulator lever through hole in bracket from the
bottom up with curve to rear of unit and secure with detent pin.
FILL ENGINE CRANkCASE
1. Add oil according to engine manual. do not overfill. Use a clean, high
quality detergent oil. Container must be marked A.P.I. Service SF - SJ.
Use no special additives with recommended oils. do not mix oil with
gasoline. Oil level must be full. Check the oil level by removing oil fill
plug. Oil level should be up to the bottom of the fill plug opening.
2. Always check oil level before starting engine. Refer to engine manual
for capacity and type of oil to use.
upper
handlebar
CAUTION !
dO NOT TRY TO LIFT ThE ROTOTILLER FROM ThE
CARTON.
IMPORTANT
ThE RIGhT ANd LEFT SIdES OF YOUR
ROTOTILLER ARE dETERMINEd FROM
ThE OPERATING POSITION AS YOU
FACE ThE dIRECTION OF FORWARd
TRAvEL.
ENGINE IS ShIPPEd FROM FACTORY
WIThOUT OIL. YOU MUST Add ENGINE
OIL BEFORE STARTING ENGINE.
NARROW TINE WIdTh
WIdE TINE WIdTh
lower
handlebar
loop
hand knob
depth
regulator
lever
detent pin