Elta 2422 - Manual (Page 10)

19. 18.
DO DO NOT
RADIO OPERATION
1. Set the BUZZ / CD / MP3 / RADIO / AUX function selector to RADIO position.
2. Set the FM ST./FM MO/AM band selector to the desired band.
3. Press the POWER button to switch on the device.
4. Rotate the ◄TUNING► control knob to the desired radio station.
Note: For better AM reception turn the unit to position the built-in directional antenna; for better
FM reception fully extend the FW wire antenna.
Note: The STEREO indicator will light when a program is received in FM Stereo. If the FM
reception is noisy, switch the band selector to the FM MO position and the program will be
received in mono.
5. Press the VOL +/- to adjust to a comfortable listening level.
6. To switch off the radio press the POWER button.
HANDLING COMPACT DISCS
• Always protect a disc against scratches and dust. If a disc is treated with reasonable care, wiping
off the disc with a soft cloth should be the only maintenance needed to retain its excellent sound
reproduction. Discs should be retained in their original cases during periods of nonuse.
• Handle a disc only by its edges. Do not touch the surface.
• Handle a disc as shown in the illustrations.
• Use a soft cloth to wipe a disc clean. Do not use benzene, thinners or other chemical cleaners as
damage may result. A disc should always be wiped in a straight line from its center to its edge.
Never wipe a disc in a circular motion.
• Do not expose a disc to direct sunlight, high humidity, or high temperatures for extended periods
of time. Do not place the disc on other equipment or near any heat source.
• Dust on the pickup lens can lead to erratic operation and skipping of the sound during playback.
To clean the pickup lens, open the disc compartment and blow the dust off. Use a camera lens
blower (available at most camera stores).
Note: Do not touch the lens. Do not allow any liquids to enter the product.
• To clean the CD player cabinet use a soft and damp cloth.
• Never use benzene or other strong chemical cleaners, as these could damage the finish.
CD PLAYBACK
NOTE: Never touch the laser lens inside the CD compartment. Clean the laser lens with a CD
cleaner disc if it becomes dirty.
1. Slide the BUZZ / CD / MP3 / RADIO / AUX function selector to CD position.
2. Open the CD compartment manually and insert a CD into the tray with label facing up.
3. Press the POWER button to turn on the unit, the disc will rotate for a few seconds and then start
playback automatically.
4. Select the previous or next track with REW. / F.FWD .
5. Press the PLAY / PAUSE button to start playback.
6. Press the PLAY / PAUSE button to pause playback, press the PLAY / PAUSE button again to
resume playback.
7. Press the STOP button to stop playback.
RANDOM PLAYBACK
• Press the REP / RAND button once, RAND will be displayed and the CD is played in random
order.
SEARCH REVERSE / FORWARD
1. Press and hold REW. / F.FWD buttons to search through the track at high speed. When
the desired track section is found, release the button and normal playback will resume.
2. Press the REW. once to skip to the beginning of the current track. Press two or more times to
skip to the previous tracks on the disc.
3. Press the F.FWD to skip to the next track on the disc.
4. Press and hold the CD Reverse Search (REW ) Button, the current track will be scanned and
move backwards to the previous track(s); When the desired track section is found, release the
button and normal play will resume.
5. Press and hold the CD Forward Search (F.FWD ) Button, the current track will be scanned
and move forward to the next track(s); When the desired track section is found, release the
selected button and normal play will resume.
REPEAT FUNCTION
Press the REP / RAND button to repeat a single track or all tracks on a CD.
1. Press the REP / RAND button once during playback, REP will be displayed. The same track will
be repeated.
2. Press the REP / RAND button a second time to repeat all tracks, ALL REP will be displayed and
the whole CD is repeated.
3. To cancel repeat mode press the REP / RAND button a third time.
PROGRAM FUNCTION
The Program feature is used to program up to 20 tracks to play in a selected order.
1. While in stop mode press the PROG. button, PROG 01 flashes in the display.
2. Press REW. / F.FWD to select the desired track.
3. Press the PROG. button to store the track into memory.
4. Repeat step 2 to 3 to select up to 20 tracks.
5. To play the selected tracks in the programmed sequence press the PLAY/PAUSE button. Track
number and PROG are displayed.
6. Press the REW. / F.FWD buttons to listen to the previous or next programmed track.
Note: After all programmed tracks have played, the CD player will return to stop mode.
7. To clear the programmed tracks from memory press STOP twice.
MP3 DISC SECTION
Note: Because MP3 discs have a large capacity, disc access times are a little longer.
1. Slide the function switch (BUZZ / CD / MP3 / RADIO) to CD position.
2. Open the CD DOOR and insert a CD into the tray with the label facing up.
3. Close the CD DOOR and press the POWER button to turn on the unit, the disc will rotate for a
few seconds and then play automatically.
4. Use the REW / F.FWD buttons to select a track.
5. Press the PLAY/PAUSE button to pause playback.
6. To stop the album temporarily, press PAUSE button, to resume, press again.
7. Press the STOP button to stop playback.