Powerfix Z29618-BS User Manual

Page 2

Advertising

GB / IE

Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
product.

To help protect the environment,

please dispose of the product properly
when it has reached the end of its use-
ful life and not in the household waste.
Information on collection points and
their opening hours can be obtained
from your local authority.

Defective or exhausted rechargeable batteries
must be recycled in accordance with Directive
2006 / 66 / EC. Return the battery and / or the
device through the appropriate collection facilities.

Improper disposal of recharge-

able batteries can damage the
environment!

Rechargeable batteries must not be disposed of
with the household refuse. They may contain toxic
heavy metals and require to be handled as special
waste. The chemical symbols of heavy metals are:
Cd = cadmium, Hg = mercury, Pb = lead

EMC

Product Description:
LED Work Lamp
Model No.: Z29618-BS
Version:

12 / 2010

Level of information: 11 / 2010
ID No.: Z29618-BS112010-6

rette lighter socket of your vehicle.

Note: The product has an overcharging
protection system. Nevertheless, you should
disconnect the LED inspection lamp from the
mains once the charging process is complete.

Note: The indicator LED

illuminates red

during the charging process. When the
charging process is complete, the indicator
LED

illuminates green. When the indicator

LED

illuminates green, pull the mains

adapter

out of the mains socket or the car

adapter

out of the cigarette lighter socket.

Disconnect the adapter from the LED inspection
lamp to prevent the batteries from discharging
themselves.

Place the rubber protection cap back on the
power input connection socket

before you

start to use the LED inspection lamp again.

Otherwise water could enter the power input
connection socket

if the LED inspection

lamp is used outdoors.

Use

m CAUTION – RISK OF ACCIDENT! If at

all possible, do not use the LED inspection lamp
in a moving vehicle. If the LED inspection lamp is
used in a vehicle, it must not be allowed to endan-
ger the safety of the driver or passengers. Always
store and secure the LED inspection lamp in such
a way that there is no risk of injury from or dam-
age to the product, even during full braking.
Note: You can secure the LED inspection lamp in
place using the hook

or magnetic mount

Clamp the magnetic mount

to the LED’s pro-

tective surround. Then hold the LED inspection
lamp against a magnetic surface.

Using the LED inspection lamp

disconnected from a power

supply

Fully charge the LED inspection lamp, as
described in the section on “Charging the
LED inspection lamp”.

Set the ON / OFF switch

to position

I to

switch on the LED inspection lamp.

Set the ON / OFF switch

to position

0 to

switch off the LED inspection lamp.

Using the LED inspection lamp

connected to a power supply

m CAUTION! RISK OF INJURY! Position the

power lead so that it does not create a trip hazard.

m CAUTION RISK OF ACCIDENT! Do not

connect or use the LED inspection lamp if you are
in moving traffic, for example driving a vehicle.
The LED inspection lamp is not intended to be
used as an indoor lighting fixture or a reading
lamp!

Remove the rubber protection cap from the
power input connection socket

Insert the power output connection plug of the
mains adapter

or of the car adapter

into the power input connection socket

the handle of the LED inspection lamp.

Insert the mains adapter

into a 230 V ~

mains socket or the car adapter

into the

cigarette lighter socket of your vehicle.

Set the ON / OFF switch

to position

I to

switch on the LED inspection lamp.

m CAUTION! If the LED inspection lamp is con-

nected to the mains by the mains adapter

in this state it is intended exclusively for
indoor use.

Set the ON / OFF switch

to position

0 to

switch off the LED inspection lamp.

Troubleshooting

Fault

Possible causes and cures

No
functions

- Mains adapter

or car adapter

is not fully inserted.

Fault

Possible causes and cures

Indicator
LED

does not
illuminate

When connected to a
cigarette lighter socket:
- Is the cigarette lighter socket

supplied with power? Some
cigarette lighter sockets only
supply power with the ignition
switched on.

- Check the fuse in the vehicle.

Charging
takes a
very long
time

When connected to a
cigarette lighter socket:
- Vehicle battery too weak?

Maintenance and cleaning

The product requires no maintenance. The LEDs
cannot be replaced.

Disconnect the product from the power supply
before you clean it.

Never immerse the product in water or other
liquids.

Do not use corrosive cleaning agents.

Clean the product regularly with a dry, fluff-
free cloth. Use a slightly moist cloth to remove
any stubborn dirt.

Disposal

The packaging is made entirely of

recyclable materials, which you may
dispose of at local recycling facilities.

IAN 58812
Milomex Ltd.
c / o Milomex Services
Hilltop Cottage
Barton Road
Pulloxhill
Bedfordshire
MK45 5HP
UK

Advertising

Popular Brands

Popular manuals