Hotpoint Ariston SL C10 BCH - Manual (Page 19)

19
it en
3. Remove any residual dirt by washing the dust
container under running water.
4. Let it dry at room temperature until all its parts
are thoroughly dry.
5. Close the dust container lid until it clicks into
place and replace it into the dust compartment.
6. Close the dust compartment lid until it clicks into
place.
Cleaning the filters (K)
version without dust bag
This model comprises two Pure Clean Hepa 13 filters.
The Pure Clean Hepa 13 filter ensures maximum
protection against allergens and high air quality,
because the air given back by the appliance is entirely
free from dust/powder residues (filtering power >
99.95 %).
To clean the Pure Clean Hepa 13 filter (31) in the
back:
1. Disassemble the air grill (33) using the opening
tab.
2. Remove the Pure Clean Hepa 13 filter by
releasing the opening tab.
3. Wash the filter under running water, taking care
that the jet of water is not too strong.
4. Hold it so that the water flows parallel to its folds.
5. Let it dry at room temperature until all of it’s parts
are thoroughly dry.
6. Re-place the Pure Clean Hepa 13 filter, paying
attention to the positions of the notches.
7. Fit the air grill into its housing until it clicks into
place.
To clean the dust compartment filters (40):
8. Press the dust-compartment opening button (14)
to open the dust compartment (15).
9. Remove the dust container (41).
10. Release the opening tab and then remove the
Pure Clean Hepa 13 filter, pre-filter (43) and filter
protection grill (42).
11. When cleaning the filter protection grill, remove
any dust/powder residues with a small brush. If
needed, use a damp soft cloth.
12. Clean the pre-filter by washing it under running
water, taking care that the jet of water is not too
strong. Allow to dry.
13. Wash the Pure Clean Hepa 13 filter under
running water, taking care that the jet of water is
not too strong.
14. Hold it so that the water flows parallel to its folds.
15. Let it dry at room temperature until all its parts
are thoroughly dry.
the correct position to allow lid closure.
Cleaning the filters (I)
version with dust bag
The Pure Clean Hepa 13 filter ensures
maximum protection against allergens and
maintains high air quality, as the air given back
by the appliance is entirely free from dust/
powder residues (filtering power > 99.95 %).
To clean the Pure Clean Hepa 13 filter (31):
1. Disassemble the air grill (33) using the opening
tab.
2. Remove the Pure Clean Hepa 13 filter by
releasing the opening tab.
3. Wash the filter under running water, taking care
that the jet of water is not too strong.
4. Hold it so that the water flows parallel to its folds.
5. Let it dry at room temperature until all its parts
are thoroughly dry.
6. Replace the Pure Clean Hepa 13 filter, paying
attention to the position of the notches.
7. Fit the air grill into its housing until it clicks into
place.
To clean the dust compartment filters (40):
8. Press the dust-compartment opening button (14)
to open the dust compartment lid (15).
9. Remove the Pure Clean dust bag (36), motor
filter grill (38) and motor filter (37) from the motor
filter grill.
10. Clean the motor filter by washing it under running
water, taking care that the jet of water is not too
strong. Then gently shake water loose.
11. When cleaning the motor filter grill, remove
any dust/powder residues with a small brush. If
needed, use a damp soft cloth.
12. Fit the motor filter into the motor filter grill again,
taking care to position it gently into the special
notches.
13. Slide the motor filter grill assembly into the
special guides in the dust compartment.
14. Fit the Pure Clean dust bag using the special dust
bag support.
15. Close the dust compartment lid until it clicks into
place.
Cleaning the dust container (J)
For the routine cleaning of the dust container:
1. Press the dust-compartment opening button (14)
to open the dust compartment (15) and remove
the dust container (41).
2. Open the lid and empty the dust container.