Whelen 7110501 - Manual

Page 1
Model(s):
7110501 (14V Green)
7110502 (14V Red)
Model(s):
7110503 (28V Green)
7110504 (28V Red)
Model(s):
7110513 (28V Green)
7110514 (28V Red)
1.08
1.08
1.08
.67
1.25
1.25
1.25
RED (+14VDC)
BLACK (-)GROUND
20 AWG 6.00” ±1.00”
1.15
1.15
SJS840351 Connector
POS A = 28VDC, WHT
POS B = Ground, BLK
POS C = Chassis, GRN
Model(s):
7110511 (28V Green)
7110512 (28V Red)
1.08
1.25
1.15
WHITE (+28VDC)
WHT/BLU (-)GROUND
SHIELD
2 CONDUCTOR
20 AWG ETFE CABLE
LEAD LENGTH
12.00” ±1.00”
WHITE (+28VDC)
BLACK (-)GROUND
20 AWG 6.00” ±1.00”
20 AWG/MIL 22759/43
Lead Length -
6.00” +1.00”,-0.5”
Model(s):
7110505 (28V Green)
7110506 (28V Red)
1.08
1.25
1.15
1/8" EXPANDABLE SLEEVING
TYPE: EXPANDO 686DM BLACK
POS. A
POS. B
POS. C WHT (28VDC)
N/C
BLK (GND)
The conditions and tests required for TSO approval of this article are
minimum performance standards. It is the responsibility of those
installing this article either on or within a specific type or class of
aircraft to determine that the aircraft installation conditions are within
the TSO standards. TSO articles must have separate approval for
installation in aircraft. The article may be installed only if performed
under 14 CFR part 43 or the applicable airworthiness requirements.
®
ENGINEERING COMPANY INC.
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: [email protected]
Aviation
Installation Guide: 71105( )-series
Models 7110501, 02, 03, 04, 05, 06, 11, 12, 13, 14
P/N: 01-0771105-01, -02, -03, -04, -05,
-06, -11, -12, -13, -14
LED Forward Position
Light Assembly
©2012 Whelen Engineering Company Inc.
Form No.14650B (072414)
TSO-C30c
TYPES I & II
APPROVED
MADE IN THE U.S.A.
OPERATING INSTRUCTIONS:
Operational Voltage: . . . . . . . . . . . . 14/28 VDC (nominal)
Input Current:. . . . . . . . . . . . . . . . . . 0.25 Amps
EQUIPMENT LIMITATIONS: An approved forward position
lighting system consists of two lights, one located on each
wingtip.
Certain types of installations may require additional testing.
CONTINUED AIRWORTHINESS: The 71105 series LED wingtip
position light assembly is designed with either 3 Green LED’s or 4
Red LED’s. If any one LED fails, the unit must be repaired or
replaced. Inspect the lens. Replace if there is excessive
scratching, discoloration or cracking.
Note: To reduce eye strain, use an optical filter such as dark
glasses or a blue covering dome during LED inspection.
INSTALLATION PROCEDURES: The following information is to
assist in the installation of a Whelen LED Forward Position Light
System.
1.
Choose the appropriate 71105( ) series replacement light
assembly.
2. The installation procedure described in the following text will
be confined to a single light installation, but is identical for
multiple light installations.
3. Remove the old light, locate and save the existing +VDC
lead and (-) ground lead. Clean and prep ends as required.
4. Make sure the existing system is equipped with an
appropriate sized breaker. Connect the existing
+14/28 VDC lead to the POSITIVE wire on the input cable
assembly (supplied with the light assembly). Connect the
existing ground lead to the GROUND wire on the input
cable assembly or use the supplied connector as shown in
the illustrations. Both leads must be connected by an
approved FAA connection. Insure that the wire leads clear
of any obstructions and ty-wrap as required.
5. Remove the shroud from the light assembly.
6. Position the base of the new light assembly onto the
mounting surface. Insert three (3) #6-32 pan head screws
into the mounting hole and tighten firmly. Reinstall the lens
so that the two notches are positioned under the shroud,
with each notch equidistant to the centerline.
7. Check all avionics systems for interference from the
installation.
8. A flight check should be performed by a properly certified
pilot.
9. Update aircraft records, complete Form 337 and obtain FAA
field approval for installation as necessary.