Avago Technologies LSI SAS 3080X-R - Manual

Quick Installation Guide
LSISAS3080X-R PCI-X to 3.0 Gbit/s SAS Host Bus Adapter
Thank you for purchasing the
LSISAS3080X-R PCI-X to 3.0 Gbit/
s Serial Attached SCSI (SAS) Host
Bus Adapter (HBA). Please take a
few minutes to read this quick
installation guide before you
install the LSISAS3080X-R.
If you need more information
about any topic covered in this
guide, refer to the other
documents on the accompanying
LSI Logic Device Drivers &
Utilities CD.
Contents of the LSI Logic Device
Drivers & Utilities CD
The LSI HBA CD contains utility programs,
device drivers for various operating
systems, and the following LSI
documentation:
• PCI-X to 3.0 G/bit Serial Attached SCSI
(SAS) Host Adapters User’s Guide
• Fusion-MPT™ Device Management
User’s Guide
• LSI HBA technical product briefs
Q U I C K H B A I N S T A L L A T I O N
To install the LSISAS3080X-R, follow these steps:
1. Unpack the HBA and inspect it for damage. Unpack the HBA in a static-free
environment. Remove the HBA from the antistatic bag and inspect it for damage. If it
appears to be damaged, or if any component is missing, contact LSI Logic or your reseller
support representative.
2. Prepare the computer. Turn off the computer and remove the power cord from the
back of the power supply. Remove the cover from the chassis. Be certain to disconnect the
computer from the power supply and from any networks before installing the controller card.
3. Insert the LSISAS3080X-R in an available PCI/PCI-X slot. Locate an empty PCI/PCI-X
slot. Remove the blank bracket panel on the back of the computer that is aligned with the
PCI/PCI-X slot you have selected. Save the bracket screw when present. Align the HBA to
a PCI/PCI-X slot. Press down gently but firmly to properly seat the HBA in the slot. The
following figure illustrates how to insert the HBA in a PCI/PCI-X slot.
NOTE: The LSISAS3080X-R is keyed for a 3.3 V slot. The keying of edge connector J1 prevents the
card from being installed in a 5 V slot.
4. Secure the bracket to the system’s chassis. Install the bracket screw, when present, or
engage the system retention mechanism to secure the HBA to the system’s chassis.
5. Connect the serial cable(s) between the HBA and the serial hard disk drive(s) (HDD).
The LSISAS3080X-R has two internal X4 SAS connectors, each connecting to four 3 Gbit/s
SAS ports. The HBA must be connected to SAS storage devices using the appropriate
cable. For connection to internal drives or backplanes, an internal cable with a standard
SAS Internal Wide Port connector (SFF-8484) on the controller side of the cable is
required. The other end of the cable may fan out into four cables with either SATA-style
signal connectors or SAS device connectors at the end for direct connection to disk drives
(and some backplanes) or single SAS Internal Wide Port connector for backplane
attachment. The following figure illustrates the connector locations on the LSISAS3080X-
R and the use of a controller-based, fan-out cable to connect to drives that require a
SATA-style signal connector.
Make a backup of your data before changing your system configuration.
CAUTION
32-Bit Slots
64-Bit Slots
(3.3 V)
(3.3 V)
Edge of
Host Board
Bracket
Screw
HDD
Connector
Serial Signal
Cables
HBA to HDD
4-Lane Internal
HBA Connector
SFF-8484
Breakout Cable
Press Here
Press Here
Note:
The HBA shape, size, and locations of
components may vary from this
illustration.
32653-00