Extron electronic MTP DA4 - Manual

Power Supply
Output Cord
SECTION A–A
Ridges Smooth
A A
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
This card provides quick start instructions for an experienced
installer to set up and operate any of the MTP DA
distribution amplifier.
Pre-installation — Jumpers
Refer to the MTP DA Series User’s Guide for more
information.
N
The jumpers have no effect when the
DA is part of an MTP CV/SV series,
or VTT001/VTR001 system.
Jumper J3 sets the DA for either audio
(default) or serial data in addition to the RGB
video.
Jumper J9 sets the DA to either always pass
the audio or serial link regardless of the
contact closure mute status (default), or to
mute the audio or serial link when its video
mute function is activated.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP DA as required.
Step 2 — Input from the transmitter
Terminate a TP cable as shown at right. Connect
it between an MTP transmitter and the A/V Input
connector.
Step 3 — Outputs to the receivers
Terminate up to four or eight TP cables as shown at
right. Connect them between the DA’s A/V Output
port and receivers that are compatible with the
transmitter .
N The input and all outputs should all be
terminated using the same standard on both
ends of the cables.
Step 4 — Power
Wire the 2-pole captive screw connector for the included
external 12 VDC power supply as shown at right. Plug it into
the DA.
Setup Guide — MTP DA4 and DA8
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-975-50
Rev. A 01 09
Example of a typical MTP DA8 application
1 2 3 4 A/V INPUT A/V OUTPUTS
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
1234567 8
1 2 3 4 A
OUTPUT MUTE
0.5 A M AX 12V POWE R + -
OUTPUT M UT E
1 2 3 4 5 6 7 8 A
INPU T 1 2 3 4 5 6 7 8
OUTPUT S
OUTPUT SHAR P L R
INPU T VIDEO 12V 0.5a MA X MT P R SV A
OUTPUT SHAR P L R
INPU T VIDEO
12V 0.5a MA X MT P R SV A
OUTPUT SHAR P L R
INPU T VIDEO
12V 0.5a MA X MT P R SV A
OUTPUT SHAR P L R
INPU T VIDEO 12V 0.5a MA X MT P R S V A
INPU T
MTP T SV A RC A
VID EO OUTP UT
L R 12V 0.5 a MA X
Flat Panel
Display
Extron
MTP DA8
Mini Twisted Pair
Distribution Amplifier
Up To
8 Receivers
Extron
MTP T AV RCA
Twisted Pair
Transmitter
DVD
Extron
MTP R AV
Twisted Pair
Receivers
TP Cable
TP Cable
Setup Guide — MTP DA4 and DA8, cont’d
A
S
A
S
A
S
J9
Disable
Mute
(Default)
or Enable
Mute
A
S
A
S
A
S
J3
Serial
(Default)
or Audio
Operation — Mutes
To mute an output, tie that ouput’s Output Mute pin to ground (_).
To mute all outputs, tie the A pin to ground.