Roland PDA120L-BK V-Drums Acoustic Design 12" Tom Pad - Manual

Before using this unit, carefully read the leaflet “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the
document(s) where it will be available for immediate reference.
© 2020 Roland Corporation
Names of Parts
Hoop rubber Head
Tuning bolt
Shell Lug
Hoop
(rim)
Hand knob
Bracket
(PDA120L, PDA100L
only)
Output jack
* The illustration shows the PDA120L.
NOTE
Due to the characteristics of the materials used in the sensor, the
strike feel of the head and the sensitivity of the sensor may be
affected by changes in temperature and humidity.
Mounting on a Stand
PDA120L, PDA100L only
Tom holder
Loosen
Allowable diameter of mounting rod: 9–13 mm (3/8–9/16 inches)
Connecting to the Drum Sound Module
Using the included connection cable (stereo cable) or the
dedicated connection cable included with your drum sound
module, attach the pad to your drum sound module.
Connect the L-shaped plug of the connection cable to the pad’s
output jack.
Using a mono cable will NOT allow rim shots.
* To prevent malfunction and equipment failure, always turn
down the volume, and turn off all the units before making any
connections.
L-shaped
plug
I-shaped
plug
To Output jack
Example: Drum Sound
Module TD-17
Connection cable
(Accessory)
Recommended Parameter Settings
These are the recommended setting values for the trigger
parameters when using the PDA120LS, PDA120L, or PDA100L
with your drum sound module.
Choose these if “PDA120LS/PDA120L/PDA100L” is one of the
choices for “PAD TYPE” or “TRIG TYPE” on your drum sound
module.
If “PDA120LS/PDA120L/PDA100L” is not one of the choices, then
refer to the support information on the Roland
website.
http://roland.cm/trigger_prm
You might need to adjust the trigger parameters
depending on the conditions of use, such as the mounting
method or the position of the PDA120LS, PDA120L, or PDA100L.
For details on these settings, refer to the owner’s manual of your
drum sound module.
Adjusting the Head Tension
Before playing, you must adjust the pad tension first.
If the head is too loose, the sensor might not work correctly,
or the sensor might be damaged. For stable operation, adjust
the head tension slightly tighter than the strike feel of a typical
acoustic drum.
NOTE
To avoid faulty operation, observe the following points.
5 Adjust the head evenly so that it does not sag.
5 Adjust the tuning bolts so that they are not loose.
1. Adjust each tuning bolt little by little, across the head
as indicated in the illustration.
Head
Tuning bolt
2 1
5 3
4 6
NOTE
Fully tightening a tuning bolt at only a single location produces
uneven tensioning, and correct playing dynamics may not
be achieved or may even cause malfunctions. Even tuning/
tensioning is very important.
2. Adjust the tightness of each tuning bolt so that the
head is tensioned evenly.
MEMO
5 Head tension will not affect the actual tuning of the sound you
are playing. For that you need to adjust sound parameters in
the drum sound module you are using. For details, refer to the
owner’s manual of your drum sound module.
5 Also, head tension may change depending on usage. Adjust
as needed.
Replacing the Head or Hoop Rubber
The performance of the head and/or hoop rubber will diminish
with use over time. If the head is torn or becomes too fatigued, or
impossible to tension correctly, then it should be replaced. If the
hoop rubber is worn out, it too can be replaced.
For replacement heads or to have the hoop rubber replaced,
please contact your dealer or a Roland service center.
Replacing the Head
NOTE
Applying excessive force to the sensors located under the head
can damage them and/or interfere with accurate triggering.
PDA120LS, PDA120L
Head
Hoop
Sensor
* The illustration shows the PDA120L.
PDA100L
Sensor
1. Remove all tuning bolts.
Go around and loosen each bolt a little at a time by turning it
counter-clockwise.
2. Remove the hoop and old head.
* Take care not to touch the sensor with your hand.
3. Place the new head and hoop on the shell.
4. Install all six tuning bolts.
5. Adjust the tension of the head.
Playing Methods
Head shot
Hit only the head of the pad.
Head shot
MEMO
For details on the sounds that are supported, refer to the owner’s
manual of your drum sound module.
Rim shot
Strike the head and the rim of the pad simultaneously.
A sound (rim sound) different than the head shot will be heard.
Rim shot
Head shot
Main Specifications
Roland PDA120LS, PDA120L, PDA100L: V-Pad
PDA120LS PDA120L PDA100L
Shell
12 (diameter) x 4 (depth) inches
Wood shell 10 (diameter) x 4 (depth) inches
Wood shell
Head 2-ply mesh head
Triggers 2 (Head, Rim)
Connector Output jack
Allowable diameter of
mounting rod
– 9–13 mm (3/8–9/16 inches)
Dimensions
345 (W) x 324 (D) x 125 (H) mm
13-5/8 (W) x 12-13/16 (D) x 4-15/16 (H)
inches
345 (W) x 380 (D) x 125 (H) mm
13-5/8 (W) x 15 (D) x 4-15/16 (H) inches 295 (W) x 330 (D) x 125 (H) mm
11-5/8 (W) x 13 (D) x 4-15/16 (H) inches
Weight
2.0 kg
4 lbs 7 oz 2.3 kg
5 lbs 2 oz 1.9 kg
4 lbs 4 oz
Accessories Owner’s Manual, Leaflet “USING THE UNIT SAFELY,” Connection cable, Drum key
This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to
the Roland website.
Owner’s Manual PDA120LS PDA120L PDA100L V-Pad English
1
When you need repair service, access this URL and find your nearest Roland Service Center or
authorized Roland distributor in your country.
http://roland.cm/service
Roland Service Centers and Distributors Roland Service Centers and Distributors
When you need repair service, access this URL and find your nearest Roland Service Center or authorized Roland distributor in
your country.
http://roland.cm/service
Roland Service Centers and Distributors Roland Service Centers and Distributors
When you need repair service, access this URL and find your nearest
Roland Service Center or authorized Roland distributor in your country.
http://roland.cm/service
Roland Service Centers and Distributors Roland Service Centers and Distributors