Roland TD-07DMK V-Drums Electronic Drum Set - Manual

1
Drum sound module / Pads / Others
2
Drum stand
3 4
Connection procedure
5
Setup Guide
© 2021 Roland Corporation
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaflet “USING THE UNIT SAFELY,” “TD-07 Owner’s Manual,” and the Setup Guide).
After reading, keep the document(s) where it will be available for immediate reference.
Check the included items As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
* This package does not include a kick pedal. Use with a commercially available kick pedal.
Assemble the drum stand
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat
(TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.
* The drum stand assembly procedure is for right-handed players. If you want to set up the stand for left-handed players, refer to
“Assembly for left-handed players” in the lower right.
Attach the parts Connect the pads to the drum sound module (TD-07)
* Insert the plug firmly,
making sure it’s all
the way in.
1. Connect the connection cable to the
drum sound module as shown in the
illustration below.
Insert the connector all the way, then
turn the knobs to fasten it securely.
2. Labels are affixed to the
connection cable to indicate
the pads to be connected. Make
connections as shown in the
illustration at right.
Connect the AC adaptor and headphones/speakers
Connect the AC adaptor, headphones, or speakers as
described in the “TD-07 Owner’s Manual.”
* To prevent malfunction and equipment failure,
always turn down the volume, and turn off all the
units before making any connections.
For a left-handed setup
Assemble the drum stand as described in
“Assembly for a left-handed players” of section
“
2 Assemble the drum stand”; then attach the
parts and connect the cables as shown in the
illustration at right.
9 When you’ve finished making connections, turn on the power as described
in the “TD-07 Owner’s Manual,” and verify that you can hear sound. This completes assembly and connections.
* Adjust the position and height of the pads and pedals according
to your height and tastes, so that they are easy to play.
* To prevent the drum stand from tipping over,
do not position the stand leg pipes at the two
ends more than 1.2 meters (48 inches) apart. CY-5
CY-5
PDX-6A PDX-6A
CY-5 TD-07
PDX-8 PDX-6A
Hi-hat control
pedal
8 Hi-hat control
pedal 8 Cymbal pad for hi-hat/crash/ride
(CY-5 x 3) 8 V-Pad for tom
(PDX-6A x 3)
8 Setup Guide (this document)
8 Owner’s Manual set
8 V-Pad for snare
(PDX-8)
1. Attaching the parts for the kick
1–1. Remove the cap that is attached to the 1
main unit’s right pipe (with one holder).
1–2. Insert the kick pad and mount holder (for the
pedal plate), and provisionally fasten them in
the orientation shown in the illustration.
Kick pad
Mount holder
(for the pedal plate)
Cap
Wide Narrow
1–3. Replace the cap.
1–4. Attach the pedal plate to the mount holder.
Pedal plate
2. Assembling the left and right arm sections
* Lay the left and right arm sections on the floor
while assembling them.
Left arm section
2–1. Using a drum key, loosen the bolt on the
holder of straight pipe “L” (long)
3 , then
insert curved pipe 2 .
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
2–2. After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
Curved pipe
Straight pipe L (Long)
Holder
Bolt
Guide hole
3
2
Drum key
2–3. Use the drum key to loosen the bolt of the
drum sound module holder, then attach the
drum sound module holder to straight pipe
“L” (long)
3 and tighten the bolt.
Straight pipe L
(Long)
Bolt
Drum sound module
holder
3
Right arm section
2–4. Using a drum key, loosen the bolt on the
holder of straight pipe “R” (short)
4 then
insert curved pipe 2 .
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
2–5. After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
Curved pipe
Straight pipe
R (Short)
about 7 cm (3 inches)
Holder
Bolt
Guide hole
4
2
2–6. Position straight pipe “R” (short) 4 so that its
tip protrudes by about 7 cm (3 inches), and
then tighten the holder.
3. Attach the left/right arm sections to the main unit
3–1. Use a drum key to loosen bolt of the holder
“A” attached to the left-side pipe (with two
holders) of the main unit
1 , and insert left
arm (of the assembly you created in step 1)
into holder “A” of the main unit.
Holder A
Bolt
Curved pipe
Main unit
Left arm
1
2
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
Bolt
Guide hole
3–2. After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
3–3. Lower the holder “B” attached to the main
unit
1 ’s right pipe, moving it down to the
position shown in the illustration.
Holder B
about 7 cm (3 inches)
3–4. Use the drum key to loosen bolt of the holder
“B,” and insert right arm (of the assembly you
created in step 1) into holder “B” of the main
unit
1 .
Holder B
Bolt
Curved pipe
Right arm
2
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
Bolt
Guide hole
3–5. After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
4. Attaching the snare pipe
4–1. Use the drum key to loosen bolt of the holder
“C,” and insert the snare pipe
5 into holder
“C” of the main unit 1 .
4–2. After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
* Insert the end of the snare pipe that doesn’t have a cap on it
into holder “C.”
Snare pipe
Holder C
Cap
Bolt
5
5. Adjusting the vertical pipes
5–1. Place the main unit 1 upright, then loosen
the hand knobs of holders “A” and “B.” Next,
spread open the pipes at left and right.
5–2. Adjust to an angle at which the drum stand
can remain upright on its own, and then
tighten the hand knobs (two locations) that
you loosened.
5–3. Verify that the four vertical pipes are truly
vertical.
If the stand wobbles, loosen the bolts on the
holders of straight pipes “L” (long)
3 and “R”
(short) 4 and adjust the height. After adjusting
the height, tighten the bolts on the holders.
Bolts on the holder
Hand knobs of
holders A and B
6. Attaching the pad mounts
NOTE
The tips of the mounts are sharp. Handle them with
care.
Main unit/snare pipe
6–1. Attach mount holders 8 to the top of the
main unit 1 and tighten the respective hand
knobs.
Mount holders
Hand knobs
8
6–2. Attach the pad mounts 9 to mount holder
8 , and firmly tighten the respective hand
knobs.
Pad mounts
Hand knobs
9
6–3. Attach mount holder 8 to the snare pipe 5 ,
and tighten the hand knob.
Mount holder
Hand knob
8
6–4. Attach pad mount (with memory clamp) 10
to the snare pipe 5 , and tighten the hand
knob.
(with the memory clamp)
Hand knob
Pad mount
10
Right arm
6–5. Attach pad mount 9 to the mount holder
8 , and tighten the hand knob.
Mount holder
Hand knob
Pad mount 9 8
7. Attaching the cymbal mounts
7–1. Insert the hi-hat and ride cymbal mounts
(short)
6 and the crash cymbal mount
(long) 7 into the holder of the curved pipe
2 , and adjust the position and direction
of all holders as shown in the illustration to
complete the setup.
Cymbal mount (Short) Cymbal mount (Short)
Cymbal mount (Long)
Pad mounts
Pad mount
Pad mount
Kick pad
Pedal plate
(with memory clamp)
6 6
7
9
9
10
The ball portion
should be visible by
the player
Ball
NOTE
5 When setting-up or adjusting the drum stand, take care not to pinch your fingers between movable parts and the main unit. If using this in a location where children
are present, be sure to provide adult supervision or guidance.
5 Prepare an area in which you can perform the assembly safely.
5 Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
No. Name Quantity
1 Main unit 1
2 Curved pipe 2
3 Straight pipe L (Long) 1
4 Straight pipe R (Short) 1
5 Snare pipe 1
6 Cymbal mount (Short) 2
7 Cymbal mount (Long) 1
8 Mount holder 3
9 Pad mount 3
10 Pad mount (with the memory clamp) 1
11 Cable clip 4
12 Cable tie 2
Use caution regarding the
following to prevent the drum
stand from falling over.
5 Adjust the rod height so
that no part of any cymbal
is higher than 1.2 meters (48
inches) above the floor.
5 Attach the cymbals in
such a way that the
center of the cymbal
does not extend
beyond the rear pipes
of the stand.
Adjusting the position of the cymbal
Attach the kick pedal
1. Mount the kick pedal to the
pedal plate. 2. Adjust the position of
the kick pad and the kick
pedal so that the beater
strikes the center of the
kick pad when you step
on the kick pedal. 3. Once the kick pad and kick
pedal are in the desired
playing position, tighten
the hand knobs.
Verify that the plate and pedal firmly
contact the floor without any gap
Install the kick pedal
securely.
1.2 m (48 inches)
Cabling diagram for the connection cable
(As seen from the back)
* Fasten the cables so that they will
not obstruct your playing; use
cable clips
11 and cable ties 12 .
Make sure to wrap the cable ties
around the pipes.
Attach the hi-hat (CY-5), crash cymbal/ride cymbal (CY-8)
PDX-6A
TD-07
Hi-hat control pedal
(T1)
PDX-6A
(T2)
PDX-6A
(T3) PDX-8
(SNR)
CY-5
(HH)
CY-5
(RD)
CY-5
(CR1)
CR1
T2 T1
T3
HH
SNR
TD-07
HHC
KIK
RD
CR2
Cabling diagram for the connection cable
(As seen from the back)
CR1
T2 T1
T3
HH
SNR
TD-07
KIK
HHC
RD
NOTE
When handling the hi-hat control pedal, kick pedal, or cymbal pads, take care not to
pinch your fingers between movable parts and the main unit. If using this in a location
where children are present, be sure to provide adult supervision or guidance.
* When attaching the PDX-8 (snare),
refer to “About the memory clamp”
on the other side.
* 5 1 0 0 0 7 6 4 3 8 - 0 1 *
“CR2” is not used. It is used when
you are adding a cymbal using a
separately sold cymbal pad and
cymbal mount (MDY-Standard). If
you are not adding this, leave the cap
attached. Fasten it so that it does not
obstruct your performance.
* PDX-6A does not support
the use of the rim-shot
technique.
OK Not OK
TD-07DMK
8 AC adaptor 8 Connection cable 8 Kick pad 8 Pedal plate 8 Drum sound
module holder 8 Mount holder
(for the pedal plate) 8 Drum sound module
(TD-07) 8 Drum key
1
2
3
Knob
4 5 6 7
8
9
10
11
12
Assembly for a left-handed players
If you want to use a left-handed setup, assemble the
stand as follows.
5 Reattach the holders attached to the main unit 1 ’s pipes
so that there are two holders on the right and one on
the left.
5 Attach the kick pedal and the pedal plate to the left side
of the main unit 1 .
5 Assemble the left and right arm sections so that straight
pipe “R” (short) 4 is at the left and straight pipe “L” (long)
3 and the drum sound module holder are at the right,
and attach them to the main unit 1 .
5 Attach the snare pipe 5 to the right side of the main
unit 1 .
5 Attach the pad mounts 9 10 and cymbal mounts 6 7 as
shown in the illustration.
Label
“CR2” is not used. It is used when you are adding a cymbal
using a separately sold cymbal pad and cymbal mount (MDY-
Standard). If you are not adding this, leave the cap attached.
Fasten it so that it does not obstruct your performance.
Beater
Kick pad
Hand knob
Cymbal mount (Short) Cymbal mount (Short)
Cymbal mount (Long)
Pad mounts
Kick pad
Pedal plate Straight pipe R (Short)
Pad mount
Straight pipe L (Long)
Pad mount
(with the memory clamp)
6 6
7
9
9
10
4 3
Snare
pipe
5
Drum
sound
module
holder
1. Position the cymbal so that the stopper (convex
portion) of the cymbal mount is aligned with the
concave portion of the bottom of the cymbal. 2. Hi-hat:
Tighten the cymbal nut enough to prevent the pad from
wobbling when you strike it.
Crash/Ride cymbal:
Tighten the cymbal nut enough to allow an appropriate
amount of sway.
* Use the cymbal nut and felt washer that are included with the drum stand.
“Roland” logo on the
farther side
Cymbal nut
Felt washer
Stopper
(convex
portion)
Attach the drum sound module
(TD-07)
Use the bolt of the drum sound module
holder to attach it as shown in the
illustration.
Attach the snare (PDX-8)
and toms (PDX-6A)
Loosen
Tighten
Pad mount
Power cord
to AC outlet AC adaptor
Headphones
Amplified speaker
etc.
CR2
1.2 m
(48 inches)
OK