Roland Boutique TB-03 Bassline Synthesizer User Manual

Tb-03

Advertising

Owner’s Manual

Bass Line

TB-03

System Settings

Hold down the

[FUNCTION] button and turn the

[VALUE] knob to select a parameter.

When you release the

[FUNCTION] button, the parameter is finalized and the value is

displayed.

Use the

[VALUE] knob to set the value.

Press the

[FUNCTION] button, to exit the system settings.

Display Parameter

Value

Explanation

MIDI Channel

–

OFF

Specifies the MIDI transmit/receive channel.

SYnC

MIDI Clock

Source

AutO

If MIDI clock is input from the MIDI IN connector or the USB port, the

tempo automatically synchronizes to MIDI clock (default). If MIDI clock

is input simultaneously from the MIDI IN connector and the USB port,

the USB port takes priority.

Int

The tempo operates according to the TB-03’s own setting. Use this

setting if you don’t want to synchronize with an external device.

NiDi

The tempo synchronizes to MIDI clock being input from the MIDI IN

connector.

USB

The tempo synchronizes to MIDI clock being input from the USB port.

thrv

Soft Thru

Off

Specifies whether data received from the MIDI IN connector will be

retransmitted from the MIDI OUT connector (On: default) or will not be

retransmitted (OFF).

A.OFF

Auto Off

OFF

The power does not turn off automatically.

(min)

The power turns off automatically after 30 minutes (default).

* Auto Off does not occur while USB-connected.

dENO

LED Demo

OFF

Specifies the time until the LED DEMO is shown (default: 3).

(min)

NoDE

Step

Recording

Mode

OrG

This is original mode, which reproduces the TB-303’s pattern write

operation (default setting).

This mode uses a unique concept in which pitch and timing (time) are

entered using separate processes, and requires practice in order to

enter the phrase that you intend. Although this mode requires complex

operation, it can result in some remarkable phrases being created by

accident, so please try using it.

StEP

This is step recording mode, which was newly added on the TB-03.

You can enter notes while watching the step number in the display.

Compared with original mode, this mode makes it easier to enter

the phrase that you intend. We recommend that beginners start by

learning this mode.

Overdrive

Type

This is the high-gain overdrive sound of the BOSS OD-2.

This gives a basic, traditional distortion sound.

Produces a distortion sound with both the smoothness of an overdrive

along with a deep distortion.

D. Typ

Delay Type

Tape

Tape Echo

diGi

Digital Delay

Rev

Reverb

d. SnC

Delay Tempo

Sync

OFF

Delay time is synchronized to the tempo (default: off).

SynC

Playing/Recording a Pattern

Adjusting the Sound

Controller

Explanation

[WAVEFORM] switch

: Saw wave,

: Square wave

[TUNING] knob

Tuning

[CUT OFF FREQ] knob

Filter cutoff (brightness of the sound)

[RESONANCE] knob

Filter resonance (distinctive character)

[ENV MOD] knob

Envelope modulation (tonal change)

[DECAY] knob

Decay (duration of the sound)

[ACCENT] knob

Strength of accents you’ve input in the pattern

[OVERDRIVE] knob

Adjusts the overdrive.

Turning this knob fully left turns it off.

The overdrive type can be selected in the system settings.

DELAY [TIME]/
[FEEDBACK] knob

Sets the delay time and feedback.

Turning the [FEEDBACK] knob fully left turns it off.

The delay type can be selected in the system settings.

* When reverb is selected, these knobs adjust the “reverb time” and “dry:

wet.” Turning the [FEEDBACK] knob fully left turns it off.

Pattern Playback

What are patterns and tracks?

A “pattern” is performance data that divides a measure into 16 steps.

The TB-03 has 96 “patterns” and seven “tracks” in which patterns can be arranged.

Selecting PATTERN PLAY mode

Turn the

[MODE] knob to set to “PATTERN PLAY.”

Selecting a pattern

Use the

[PATT. GROUP] knob to select a pattern group (I–IV).

Pattern group “I” is selected regardless of whether you select numbers 1 or 2.

Use the

23 24

PATT. SECTION [A][B] buttons to select a pattern section (A,

B, C).

You can press the [A] and [B] buttons simultaneously to select C (both [A] and

[B] are lit).

Use the

PATTERN [1]–[8] buttons to select a pattern.

Playing patterns consecutively

When selecting a pattern, you can select multiple patterns by pressing two buttons at the same time. The

patterns you’ve selected will play consecutively. The currently-playing pattern blinks.

Playing a pattern

Press the

[RUN/STOP] button to play/stop a pattern.

Pattern transpose

Hold down the

[PITCH MODE] button and then press the

keyboard button.

Setting the tempo

In pattern play mode, the display shows the tempo.
You can press the

[TEMPO] button to see the two digits of the tempo value below the decimal point.

You can use the

[VALUE] knob to adjust the tempo.

Setting the shuffle

If you long-press the

[TEMPO] button, the shuffle value is displayed.

You can set the shuffle setting by holding down the

[TEMPO] button and turning the

[VALUE] knob

(-50–0–50, 0=Shuffle off).

Temporarily changing the number of steps in a pattern

Hold down the

[TIME MODE] button and turn the

[VALUE] knob to change the number of steps in the

pattern (1–16).

* This change in the number of steps is temporary; it is not saved. If you want to save the change, change the

number of steps in “pattern write” mode.

What is “step”?

Each pattern is divided into 16 grid locations called “steps.” One step is a 16th note long ( ).

Playing/Editing a Track

You can arrange patterns to create a track for a song.

Track Playback

Selecting TRACK PLAY mode

Turn the

[MODE] knob to set to “TRACK PLAY.”

Selecting a track

Use the

[TRACK] knob to select a track (1–7).

The display shows the measure number.

Playing a track

Use the

[BAR RESET] button to return to measure 1.

Press the

[RUN/STOP] button to play/stop a track.

Playing tracks consecutively

If you use the

[TRACK] knob to select a track (1–7) while a track is playing, the next track is played

consecutively after the last measure (D.C. measure) of the track has played.

Functions in Track Mode

You can use the following functions in either track play or write mode.

Recalling a measure number

Turn the

[VALUE] knob to specify the measure number.

Using the [FUNCTION] button to recall a measure number

Hold down the

[FUNCTION] button and use the numeric buttons ([1]–[9], [0], [100], [200]) to specify

the measure number.

Example setting:

Measure

number

Order to press

numeric buttons

Display *1

131

[100]

[3]

[1]

Lit: [100], [3], Blink: [1]

[5]

Lit/Blink: [5]

101

[100]

[1]

Lit: [100], Blink: [1]

*1 When you press the [FUNCTION] button, the lit or blinking state of the numeric buttons indicates the

current measure number.

The 10s and 100s places are lit, and the 1s place is blinking.

If the measure number consists of repeated digits such as 55 or 33, the lit and blinking states alternate at

each beat.

Setting the tempo

In track play/write mode, the display shows the measure number, but you can press the

[TEMPO] button to

make the tempo appear for three seconds.
While the tempo is shown, you can press the

[TEMPO] button to see the two digits of the tempo value

below the decimal point.
While the tempo is shown, you can use the

[VALUE] knob to adjust the tempo.

Setting the shuffle

Refer to “Pattern Playback”–”Setting the shuffle.”

Indication of D.C. (Da Capo/last measure)

What is D.C. (Da Capo)?

When playback reaches the end of the measure that is

specified as D.C., playback returns to the first measure of the

track.

Hold down the

[FUNCTION] button and press the

[D.C.] button.

The number of the measure specified as D.C. is displayed.

(Segno) indication

What are D.S. (Dal Segno) and (Segno)?

If you press the

[D.S.] (Dal Segno) button during playback,

the playback jumps to the measure that is specified as (Segno).

Hold down the [FUNCTION] button and press the

[

]

(Segno) button.

The number of the measure specified as

(Segno) is displayed.

Viewing the transpose setting

Regardless of whether you are playing back or stopped, pressing the

[PITCH MODE] button makes a

keyboard button light to indicate the transpose setting of the current measure.

D.C.

Introduction

The TB-03 is a sound module that uses cutting-edge modeling technology to faithfully model the Roland

TB-303 which went on sale in 1982. In addition to its compact size, it allows battery-powered operation and

contains a small speaker. You’ll be able to enjoy full-fledged TB-303 sound anywhere.

* The TB-03 can operate on batteries or on USB bus power. If you are using batteries, insert four AA batteries,

making sure that the batteries are oriented correctly.

* If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully

observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT

NOTES” (leaflet “USING THE UNIT SAFELY”).

* When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle

the unit carefully; do not drop it.

* When the batteries run low, the “

Bt.Lo

” blinks in the display. Replace the battery as soon as possible.

Using the TB-03 in conjunction with the DK-01 Boutique Dock (accessory)

For installation/removal/angle adjustment, refer to the DK-01’s Owner’s Manual.

Playing the TB-03 via MIDI or USB

You can also play the TB-03 via MIDI or USB. For details, refer to “Connecting Your Equipment.”

Connecting Your Equipment

* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units

before making any connections.

Micro USB (

) port

Use a commercially available USB 2.0 cable (A-microB) to connect this

port to your computer.

It can be used to transfer USB MIDI and USB audio data. You must install

the USB driver when connecting the TB-03 to your computer. Download the USB driver from the Roland

website. For details, refer to Readme.htm which is included in the download.

http://www.roland.com/support/

* Do not use a micro USB cable that is designed only for charging a device. Charge-only cables cannot

transmit data.

[VOLUME] knob

Adjusts the volume.

PHONES jack

Connect headphones (sold separately) here.

OUTPUT jack

Connect this jack to your amp or monitor speakers.

MIX IN jack

This is the audio input jack. Sound from the connected device is output

from the OUTPUT jack and PHONES jack.

MIDI connectors

You can synchronize the TB-03 with other MIDI device by using a

commercially available MIDI cable to make connections.

TRIGGER IN jack *1

You can use a mini-plug (mono) cable to connect this to a device that’s equipped with a TRIGGER OUT jack

(such as the TR-09). If a plug is inserted into this jack, the TB-03 is disconnected from its internal clock, so that its

steps advance each time a trigger pulse is received at this jack.

CV OUTPUT jack *1

You can use a mini-plug (mono) cable to connect this jack to an analog synthesizer that’s equipped with CV/

GATE input jacks.

The pitch that is played by the TB-03 is output from this jack without change. The pitch is output in the range of

-1 V–+7 V. This supports OCT/V (Hz/V is not supported).

GATE OUTPUT jack *1

This jack outputs note-on/off signals. During note-on, +12 V is output.

*1 Do not use a “stereo mini-plug” cable; it won’t work correctly.

Turning the Power On

[POWER] switch

This turns the power on/off.

* After you’ve made connections correctly, be sure to turn on the power in the order of the TB-03 first, and

then the connected system. Powering-on in the incorrect order may cause malfunctions or damage. When

turning the power off, power-off the connected system first, and then the TB-03.

* Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down,

you might hear some sound when switching the unit on/off. However, this is normal and does not indicate

a malfunction.

TB-03

MIDI device

MIDI IN

MIDI OUT

Main Specifications

Roland TB-03: Bass Line

Power Supply

Rechargeable Ni-MH battery (AA, HR6) x 4, Alkaline battery (AA, LR6) x 4, USB bus power

Current Draw

500 mA (USB bus power)

Dimensions

308 (W) x 130 (D) x 52 (H) mm

12-1/8 (W) x 5-1/8 (D) x 2-1/16 (H) inches

Weight

940 g (including batteries, excluding

Boutique Dock)

2 lbs 2 oz

Accessories

Boutique Dock: DK-01, Owner’s Manual, DK-01 Owner’s Manual, Leaflet “USING THE UNIT

SAFELY,” Alkaline battery (AA, LR6) x 4

* This document explains the specifications of the product at the time that the document was issued. For the

latest information, refer to the Roland website.

Pattern Write (TB-303 Original Mode)

Original mode and step recording mode

The TB-03 has two pattern write modes.

“Original mode” reproduces the pattern write operation of the TB-303, and “step recording mode” is newly

added on the TB-03. You can use the system setting “Step Recording Mode” to switch between these modes.

Selecting PATTERN WRITE mode

Turn the

[MODE] knob to set to “PATTERN WRITE.”

Selecting a pattern

Refer to “Pattern Playback”–”Selecting a pattern”

Setting the tempo

In pattern write mode, the display shows the step number, but you can press the

[TEMPO] button to make

the tempo appear for three seconds.
While the tempo is shown, you can press the

[TEMPO] button to see the two digits of the tempo value

below the decimal point.
While the tempo is shown, you can use the

[VALUE] knob to adjust the tempo.

Setting the shuffle

Refer to “Pattern Playback”–”Setting the shuffle”

Clearing a pattern

Hold down the

PATTERN [1]–[8] button that you want to clear, and press the

[PATTERN CLEAR]

button.

To use a triplet grid

By default, each step is a 16th note, but by holding down the

[FUNCTION] button and pressing the

[

]

button you can use a triplet grid (each step is an 8th note triplet).

Changing the number of steps in a pattern

Hold down the [FUNCTION] button and press the

[STEP] button the number of times that you want

to specify.

Example: If you want there to be eight steps, press the button eight times.

The display shows the number of steps.

* You can also change the number of steps in the pattern by holding down the

[TIME MODE] button and

turning the

[VALUE] knob (1–16).

Entering the pitches

In TB-303 original mode, you enter the notes of a pattern using separate operations to specify the pitch and the

timing. Enter the pitches first.

Press the

[PITCH MODE] button so it’s lit.

You’re in pitch entry mode.

Use the

keyboard buttons to enter the pitches.

Example: In the case of the following notes, enter pitches in the order “C, C, D#, C…”

G F D

The display shows a number (1, 2, 3…) in the order of the notes that you enter; you can use the

[VALUE]

knob to select a number.

Press the

[FUNCTION] button.

Entering octave-up or octave-down pitches

Shift the octave up or down by pressing (or holding down)

[TRANSPOSE UP] or

[TRANSPOSE DOWN],

then press a

keyboard button (Lit: ± 1 octave, Blink: ± 2 octaves).

Checking the pitches

Press the

[PITCH MODE] button so it’s lit.

Press the

[TAP] button to check the pitch of each note.

Press the

[FUNCTION] button.

If the pitches were not entered as you intended, re-enter them starting with step 1 of “Entering the pitches.”

* Note that when you re-enter the pitches, the accent and slide data you entered are lost.

Entering the timing

Press the

[TIME MODE] button so it’s lit.

You’re in time entry mode.

Use the note selector

[

](note),

[

](tie), and

[—](rest) buttons to enter the timing.

Example: In the case of the following notes, enter “

…” in that order.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

The display shows the step number; you can use the

[VALUE] knob to select the step.

When you’ve finished entering all of the steps (16 steps by default), the

[TIME MODE] button goes dark.

Checking the time

Press the

[TIME MODE] button so it’s lit.

Press the

[TAP] button to check the data of each note.

Track Write

Selecting TRACK WRITE mode

Turn the

[MODE] knob to set to “TRACK WRITE.”

Selecting a track

Use the

[TRACK] knob to select a track (1–7).

The display shows the measure number.

The pattern group that can be written to a track

The pattern group that can be written to a track is the group that is selected

by the [TRACK] knob. For example in the case of tracks 1 and 2, the pattern

group is “I.”

Writing a track

Use the

[BAR RESET] button to return to measure 1.

Press the

[RUN/STOP] button.

Loop-playback occurs during track write. The pattern that plays at this time is the pattern that was written

into measure 1.

Use the

23 24

PATT. SECTION [A][B] buttons and the

PATTERN [1]–[8] buttons to select the pattern

that is entered at measure 1.

If you want to write with transposition, hold down the

[PITCH MODE] button and press a

keyboard

button to specify the transposition key.

Press the

[WRITE/NEXT] button.

The pattern is entered, and you proceed to measure 2.

Repeat steps 3–4 to enter up to one measure before the last measure.

Select the pattern for the last measure.

Press the

[D.C.] button, and then press the

[WRITE / NEXT] button.

D.C. (Da Capo) is entered.

Press the

[RUN/STOP] button to exit the track write.

Making Corrections

If you entered something by mistake, you can correct it as follows.

Turn the

[MODE] knob to set to “TRACK WRITE.”

Recall the measure number as described in “Recalling a measure number.”

Press the

[RUN/STOP] button.

Use the

23 24

PATT. SECTION [A][B] buttons and the

PATTERN [1]–[8] buttons to re-select the pattern.

Entering D.C. (Da Capo)

Pressing the

[D.C.] button enters D.C. (Da Capo) at the current measure.

Entering (Segno)

Pressing the

[

] (Segno) button enters (Segno) at the current measure.

Press the

[WRITE/NEXT] button.

Press the

[RUN/STOP] button.

Delete

Here’s how to delete one measure from the patterns in the track.

Turn the

[MODE] knob to set to “TRACK WRITE.”

As described in “Recalling a measure number,” move to the

measure that you want to delete.

Hold down the

[FUNCTION] button and press the

[DELETE] (C #) button.

Insert

You can insert patterns into the track.

Turn the

[MODE] knob to set to “TRACK WRITE.”

As described in “Recalling a measure number,” move to

the measure at which you want to insert.

Example: If you select measure 4, the pattern is inserted

between measure 3 and measure 4.

Hold down the

[FUNCTION] button and press the

[INS] (D#) button.

Press the

[RUN/STOP] button.

Use the

23 24

PATT. SECTION [A][B] buttons and

PATTERN [1]–[8] buttons to select the pattern that

you want to insert.

Press the

[WRITE/NEXT] button.

Press the

[RUN/STOP] button.

Restoring the Factory Settings (Factory Reset)

Here’s how to return the TB-03 to its factory-set state.

While holding down the

[2] button, turn on the power.

The

[TAP] button blinks.

If you decide to cancel the factory reset, turn off the power.

Press the

[TAP] button to execute the factory reset.

When all buttons blink, turn the TB-03’s power off, then on again.

Data Backup/Restore

Backup

Connect your computer to the TB-03’s USB port via USB cable.

While holding down the

[RUN/STOP] button, turn on the power.

Open the “TB-03” drive on your computer.

The backup files are located in the “BACKUP” folder of the “TB-03” drive.

Copy the backup files into your computer.

After copying is completed, eject the USB drive and then disconnect the USB cable.

Windows

Right-click on the “TB-03” icon in “Computer” and execute “Eject.”

Mac OS

Drag the “TB-03” icon to the Trash icon in the Dock.

Turn the TB-03 power off.

Restore

As described in the procedure for “Backup” Step

–

, open the “TB-03” drive on your computer.

Copy the TB-03 backup files into the “BACKUP” folder of the “TB-03” drive.

After copying is completed, eject the USB drive and then

press the

[TAP] button

After the LEDs have completely stopped blinking, turn off the power.

Press the

[FUNCTION] button.

* You can also check by pressing the

[RUN/STOP] button to play/stop the pattern.

If the notes were not entered as you intended, re-enter them starting with step 1 of “Entering the timing.”

Entering accents and slides

Press the [PITCH MODE] button

so it’s lit.

Press the

[TAP] button to check each note. If you want to add an accent, hold down the

[TAP]

button and press the

[ACCENT] button. If you want to add a slide, hold down the

[TAP] button

and press the

[SLIDE] button.

Press the

[FUNCTION] button.

Tap Write (Entering Timing in Real Time)

* Before you continue, complete the steps for “Entering the pitches.”

Press the

[FUNCTION] button.

Press the

[RUN/STOP] button.

Press the

[PATTERN CLEAR] button.

The metronome sounds.

In time with the sound of the metronome, press the

[TAP] button at the timing at which you want

to enter the notes.

* Entering the TIE: Hold down one of the

[1]–[8] buttons and tap the

[TAP] button.

When you finish entering the first measure, the metronome stops and the pattern plays as a loop.

If the timing was not entered as you intended, re-do the procedure from step 3.

Pattern Write (Step Recording Mode)

This is the step recording mode that was newly added on the TB-03. You’ll enter notes, rests, accents, and

slides/ties while watching the step number in the display.

Select “step recording mode” in system settings

Hold down the

[FUNCTION] button and turn the

[VALUE] knob to select “

NoDE

.”

Release the

[FUNCTION] button.

Use the

[VALUE] knob to select “

StEP

.”

Press the

[FUNCTION] button.

Selecting PATTERN WRITE mode

Turn the

[MODE] knob to set to “PATTERN WRITE.”

Selecting a pattern

Refer to “Pattern Playback”–”Selecting a pattern”

Clearing a pattern

Hold down the

PATTERN [1]–[8] button that you want to clear, and press the

[PATTERN CLEAR]

button.

Step recording

Press the

[PITCH MODE] button so it’s lit.

You’re in step recording entry mode.

Use the buttons and the

[VALUE] knob to enter performance data into the steps.

The display shows the current step number (1–16). You can also use the

[VALUE] knob to move to a

different step.

* Even during step recording, you can play back the pattern by pressing the

[RUN/STOP] button.

Controller

Explanation

[VALUE] knob

Moves between steps.

Keyboard buttons

Enter a note and proceed to the next step.

[DOWN] button

Shift the octave up/down.

Lit: ± 1 octave

Blink: ± 2 octaves

[UP] button

[TIME MODE] button

While you hold down this button,

the note, tie, and rest are shown

by the lit buttons.

Note

Tie

Rest

[TIME MODE] +

[UP] button

Enters a tie and proceeds to the next step.

[TIME MODE] +

[ACCENT] button

Enters a rest and proceeds to the next step.

[ACCENT] button

Enters an accent on/off (the step does not advance).

[SLIDE] button

Enters a slide on/off (the step does not advance).

To exit the step recording, press the

[FUNCTION] button.

* For details on the following operations, refer to “Pattern Write (TB-303 Original Mode).”

Using a triplet grid

Changing the number of steps in the pattern

English

In order to use this device correctly, please carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the “USING THE UNIT SAFELY” leaflet) before use.
After reading, keep these instructions at hand for immediate reference.

Advertising

Popular Brands

Popular manuals