Elinchrom BX 500RI - Manual (Page 20)

SET Config Mode: (to configure included features)
-­­Switch­module­OFF.
-­­Hold­test­push­button­and­switch­TX­ON.
-­­Keep­test­push­button­pressed­until­STATUS­LED­is­ON.

­Check­also­EL-Skyport­PC­/­MAC­software­3.0­for­changing­Transmitter­Speed­setting.
The­EL-Skyport Transmitter­triggers­the­EL-Skyport­Receiver­modules­in­the­following­modes:
1.­ Off­­Unit­is­OFF,­no­function.
2. Select Group - Group (1 to 4).

­ Set­switch­to­Group.­and­select­Group­1­to­4.
 ­ All­corresponding­EL-Skyport­Receivers­with­the­same­selected Group (1 to 4)­are­triggered.
3. ALL­­Mode­switch­is­set­to­ALL.

­ All­corresponding­EL-Skyport­Receivers­are­triggered­regardless­of­which­Group­is­selected.
Integrated Hot-Shoe SYNC 2.5 mm Socket
Use­the­included­Sync­cable­to­connect­the­integrated­2.5­mm­Mono­Jack­socket­with­the­camera­or­
lens­PC­socket­directly.
EL-Skyport Transmitter SPEED RX Features
Compatible­with­Ranger­RX,­Style­RX,­Digital­RX,­BXRi­250­/­500,­Ranger­Quadra­AS!
If­the­EL-Skyport­Transmitter­SPEED­is­used­with­the­EL-Skyport Transceiver RX
, BXRi 250 / 500
or the Ranger Quadra AS, ­the­following­EXTRA­
features­are­available:
Depending­upon­which­Group­is­selected,­the­following­RX-unit­settings­can­be­modified:
1.­­Flash power increase in 1/10 f-stops.

­ press­push­button­+­to­increase­the­power­of­selected­Group­of­(or­ALL)­RX-units­in­1/10­f-
stops.
2.­ Flash power decrease in 1/10 f-stops.

­ press­push­button­-­to­reduce­the­power­of­selected­Group­of­(or­ALL)­RX-units­in­1/10­f-stops.
3.­ Modelling lamp toggle.

­ press­and­hold­the­push­button­+,­2­seconds­or­longer­before­releasing,
­­­­­to­toggle modelling lamp­of­the­selected­Group­of­(or­ALL)­RX-units.
Power save mode timer:
-­­After­not­using­the­Transmitter­for­30­minutes­the­Power­Save­mode­is­active.­To­reactivate­the­
­­­Transmitter,­press­the­TEST­push­button.
-­­The­Power­Save­mode­timer­can­be­configured­with­the­EL-Skyport­PC­/­MAC­software­v­3.0­and­­­­ ­
­­­­higher.
Status LED:
-­­LED­flashes­every­4­seconds­one­time­in­“Standard”­mode­and­two­times­in­“Speed”­mode.
-­­LED­intensity­correspond­to­the­battery­status­-­if­off­or­very­low­=>­exchange­the­battery.
-­­LED­is­OFF­if­the­Transmitter­is­switched­OFF­or­in­Power­Save­mode.
.
Reset to manufacturer default setting:
-­­Switch­ON.
-­­Press­test­button­for­min­10­seconds.
19
English