Everpure QC71 - Manual (Page 2)

Combined Model Name
Replacement
Cartridge Flow Rate Capacity
QC7I Triple - MC MC 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)
QC7I Triple - MC 2 MC 2 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)
QC7I Triple - MH MH 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)
QC7I Triple - MH 2 MH 2 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)
QC7I Triple - TO TO 4.5 gpm (56.7 lpm) 90,000 gal (340,650 L)
QC7I Triple - CV CV 5.0 gpm (18.9 lpm) 22,500 gal (85,170 L)
QC7I Triple - XCV XCV 5.0 gpm (18.9 lpm) 30,000 gal (113,550 L)
QC7I Triple - XC XC 5.0 gpm (18.9 lpm) 36,000 gal (136,260 L)
QC7I Triple - XC 2 XC 2 5.0 gpm (18.9 lpm) 36,000 gal (136,260 L)
QC7I Triple - 7CB5 7CB5 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)
QC7I Triple - 7CB5-K 7CB5-K 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)
QC7I Triple - 7CB5-S 7CB5-S 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)
Combined Model Name
Replacement
Cartridge Flow Rate Capacity
QC7I Quad - MC MC 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - MC 2 MC 2 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - MH MH 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - MH 2 MH 2 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - TO TO 6.0 gpm (22.4 lpm) 120,000 gal (454,200 L)
QC7I Quad - CV CV 6.6 gpm (25 lpm) 30,000 gal (113,550 L)
QC7I Quad - XCV XCV 6.6 gpm (25 lpm) 40,000 gal (151,400 L)
QC7I Quad - XC XC 6.6 gpm (25 lpm) 48,000 gal (181,680 L)
QC7I Quad - XC 2 XC 2 6.6 gpm (25 lpm) 48,000 gal (181,680 L)
QC7I Quad - 7CB5 7CB5 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)
QC7I Quad - 7CB5-K 7CB5-K 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)
QC7I Quad - 7CB5-S 7CB5-S 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)
* For individual cartridge specifications, refer to cartridge literature.
Temperature: 35-100°F (2-38°C)
Pressure:
10 - 125 psi (0.7 - 8.6 bar), non-shock
For cold water use only.
INSTALLATION
1. Use the predrilled mounting holes in the manifold bracket as guides. Mark and drill anchor holes.
Mount securely. See Figures 5-8.
2. Shut off power to machine.
3. Connect outlet port of QC7I unit to equipment served. Always use a NSF approved pipe dope
or Teflon tape at all connections. Use a backup wrench on all fittings while connecting to avoid
excessive stress on the system components.
Note: If the optional E-Series Filter is used, install a manual shut-off valve leading to the system
for servicing.
4. Connect minimum 3/8” water line to inlet side of QC7I singles. Use minimum 1/2” line for other
systems.
5. The cross fitting has a flushing valve installed on the bottom. Connect tubing to flushing valve and
run to drain.
Note: Some municipal plumbing codes and good sanitary practices require an air gap at the drain
termination point.
6. Install the cartridge(s) into the QC7I head (s) following directions on the cartridge label or as shown
in the Cartridge Change illustrations.
7. Turn on water to filter and check for leaks.
8. Flush the cartridge by running water through at full force for five minutes. This will set the filtering
media and purge air and fines, insuring maximum filter life.
9. After flushing, close the flushing valve, turn on power to equipment and plug the LPA (if so
equipped) into the electrical outlet. See illustrations.
Figure 5 – Single System
Made in U.S.A. WATER FILTER EVERPURE
3072-61 QC7I
12 0
60
20 EVERPURE
PSI PSI 0
40
1 0 0
80
OUTLET
3/8" FNPT INLET
3/8" FNPT
27.50"
5.60"
Figure 6 – Twin System
16.60"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
25.26"
Figure 8 – Quad System
24.60"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
29.69"
Figure 7 – Triple System
21"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
29.26"
Check for compliance with state and local laws
and regulations. Do not use with water that is
microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system. Systems
certified for cyst reduction may be used on disinfected
waters that may contain filterable cysts.