EAW KF360z - Manual (Page 2)

SPECIFICATIONS KF360z
DIMENSIONAL DRAWING A & E SPECIFICATIONS
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 [email protected] www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. KF360z/0002676/2 pp April 2002 Printed in USA
The 3-way full-range loudspeaker shall incorporate a vented
12-in LF transducer, a 7-in horn-loaded cone MF transducer
with Radial Phase Plug
™ , and a 1.4-in exit / 2.5-in diag-
phragm HF compression driver on a constant directivity horn.
The MF/HF horn shall have a nominal beamwidth of 65° (h) x
45° (v).
System frequency response shall vary no more than ±3 dB
from 100 Hz to 20 kHz measured on axis. In passive mode,
the loudspeaker shall produce a sound pressure level (SPL) of
92 dB SPL on axis at 1 meter with a power input of 1 watt,
and shall be capable of producing a peak output of 127 dB
SPL on axis at 1 meter. It shall handle 750 watts of amplifier
power (AES Standard) and shall have a nominal impedance of
4 ohms.
In bi-amped mode, the LF/MF section shall produce a sound
pressure level (SPL) of 91 dB SPL on axis at 1 meter with a
power input of 1 watt, and shall be capable of producing a
peak output of 126 dB SPL on axis at 1 meter. It shall handle
750 watts of amplifier power (AES Standard) and shall have a
nominal impedance of 4 ohms. In addition, the HF section in
bi-amped mode shall produce a sound pressure level (SPL) of
103 dB SPL on axis at 1 meter with a power input of 1 watt,
and shall be capable of producing a peak output of 132 dB
SPL on axis at 1 meter. It shall handle 200 watts of amplifier
power (AES Standard) and shall have a nominal impedance of
8 ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of exterior grade Baltic birch plywood
and shall employ extensive internal bracing. It shall be fin-
ished in wear resistant textured black paint. Input connectors
shall be 2x Neutrik NL4 Speakon. The system shall include a
switch allowing it to be operated in passive or bi-amp pow-
ering mode. A total of six 3-position flytracks with integral
3/8"-16 threaded mounting/suspension points (3 each top
and bottom) shall be provided. The front of the loudspeaker
shall be covered with a powder coated perforated steel grille
backed with open cell foam to protect against dust.
The 3-way full-range loudspeaker shall be the EAW model
KF360z.
PHYSICAL continued
Dimensions inches millimeters
Height 27.5 699
Width (Front) 14.8 375
Width (Rear) 9.5 241
Depth 15.4 391
Trapezoid Angle 10 degrees per side
Weights pounds kilograms
Net Weight 87 39.6
Shipping Weight 95 43.2
A
C L
(9.56)
C L A
9.87
5.00
L C C L
VIEW A-A
C L
FRONT
BOTTOM
KF360z
14.75
3.90
HANDLE
2X 3.62
5.75 (2.13)
TOP
DIMENSIONS APPLY TO
BOTH SIDES
(2.13)
2.12
6.37
7.66
20°
9.19
7.66
NOTES:
1. SYMBOL INDICATES MOUNTING POINT, 3/8-16
THREADED HOLE (FLY TRACK).
2. SYMBOL INDICATES 3.00 x 1.35 FLY TRACK.
3. SYMBOL INDICATES CENTER OF BALANCE.
4. WEIGHT APPROX. 87 LBS.
5. SHIPPING WEIGHT APPROX. 95 LBS.
ACCESS PANEL
4.00
BACK
23.23
INPUT
8.69
23.23
5.91
DIMENSIONS APPLY TO
TOP & BOTTOM
R 42.5
15.40
TOP HAT
GRILLE PARTIALLY SHOWN
27.50
Manufacturing tolerances are +/- 0.13 and +/- 1°