Emulex LightPulse LP10000ExDC-E - Manual (Page 2)

World Headquarters 3333 Susan Street, Costa Mesa, CA 92626 +1 714 662 5600
Bangalore, India +91 80 40156789 | Beijing, China +86 10 84400221
Dublin, Ireland +35 3 (0) 1 652 1700 | Munich, Germany +49 (0) 89 97007 177
Paris, France +33 (0) 158 580 022 | Tokyo, Japan +81 3 5325 3261
Wokingham, United Kingdom +44 (0) 118 977 2929
www.emulex.com
©2013 Emulex, Inc. All rights reserved. This document refers to various companies and products by their trade names. In most, if not all cases, their respective companies claim these designations as trademarks or registered trademarks. This information is provided for
reference only. Although this information is believed to be accurate and reliable at the time of publication, Emulex assumes no responsibility for errors or omissions. Emulex reserves the right to make changes or corrections without notice. This report is the property
of Emulex and may not be duplicated without permission from the Company.
Standards
· ANSI Fibre Channel: FC-PI-4, FC-FS-2, FC-FS-2/AM1,
FC-LS, FC-AL-2, FC-GS-6, FC-FLA, FC-PLDA, FC-TAPE,
FC-DA, FCP through FCP-4, SBC-3, FC-SP, FC-HBA and
SMI-S v1.1
· PCI Express base spec 2.0
· PCI Express card electromechanical spec 2.0
· Fibre Channel class 2 and 3
· PHP hot plug-hot swap
Architecture
· Single-port (LPe12000) or dual-port (LPe12002)
· 8GFC, 4GFC or 2GFC link speeds automatically
detected
· Integrated data buffer and code space memory
Comprehensive OS and Hypervisor Support
· Windows Server
· Linux
· Solaris
· VMware vSphere
· Windows Hyper-V
· Additional support is available from OEMs
and partners
Hardware Environments
· PowerPC,® SPARC,® x86, x64 and
Intel® Itanium® 64-bit processor family
Optical
· Data rates: 2.125, 4.25 and 8.5GFC (auto-detected)
· Optics: Short wave lasers with LC type connector
· Cable: Operating at 8GFC
- 50/125µm (500MHz*km BW)-up to 50m
- 50/125µm (2000MHz*km BW)-up to 150m
Physical Dimensions
· Short, low profile MD2 form factor card
· 167.64mm x 68.91mm (6.60” x 2.71”)
· Standard bracket (low profile available)
Power & Environmental Requirements
· Volts: +3.3, +12
· Operating temperature: 0° to 55° C (32° to 131° F)
· Storage temperature: -40° to 70° C (-40° to 158° F)
· Relative humidity: 5% to 95% non-condensing
· 23 degree C wet bulb
Agency Approvals
· Class 1 Laser Product per DHHS 21CFR (J)
and EN60825-1
· UL recognized to UL 60950-1
· CUR recognized to CSA22.2, No. 60950-1-03
· Baurt-certified to EN60950-1
· FCC Rules, Part 15, Class A
· ICES-003, Class A
· EMC Directive 2004/108/EEC (CE Mark)
- EN55022:2010, Class A
- EN55024:2010
· Australian EMC Framework (C-Tick Mark)
- AS/NZS CISPR22, Class A
· VCCI (Japan), Class A
· MIC (Korea), Class A
· BSMI (Taiwan), Class A
· EU RoHS Compliant (Directive 2002/95/EC)
· China RoHS Compliant
Ordering Information
LPe12000-M8
· Single-port, multi-mode optic interface
LPe12002-M8
· Dual-port, multi-mode optic interface·
LPe12002-X8
· Dual-port, single-mode optic interface
· Long wave optical transceivers – allows the board
to transmit a signal up to 1.4km when using
800-SM-LC-I, or up to 10km when using 800-SM-LC-L
LPe12100-OPT
· Emulex Certified Spare Optic Kit for LightPulse
8GFC HBAs
· QTY 1, 8GFC short wave lasers with LC-type
connecter SFP+ optic
· Compatible with all Emulex LightPulse 8GFC
Host Bus Adapters
· For use as an on-site spare optic
Additional Features
Performance features
· Doubling the maximum Fibre Channel link rate
from 4GFC to 8GFC and enhanced virtualization
capabilities help support IT “Green” initiatives
· Frame-level Multiplexing and out-of-order frame
reassembly increases link efficiency and maximizes
HBA performance.
Data protection features
· End-to-end data protection with hardware parity,
CRC, ECC and other advanced error checking and
correcting algorithms ensure data is safe from
corruption.
Deployment and management features
· Universal Boot capability allows the appropriate boot
environment to be automatically selected for any
given hardware.
· Boot from SAN capability reduces system
management costs and increases uptime.
· Detailed real-time event logging and tracing enables
quick diagnosis of SAN problems.
· Beaconing feature flashes the HBA LEDs, simplifying
their identification within server racks.
· Environmental monitoring feature helps to optimize
SAN availability.
Management Features
· The Emulex OneCommand Manager application
enables centralized discovery, monitoring, reporting,
and administration of Emulex adapters on local and
remote hosts. Powerful automation capabilities
facilitate remote driver parameter, firmware and boot
code upgrades. Advanced diagnostic features such
as adapter port beaconing and adapter statistics help
to optimize management and network performance
while the environmental monitoring feature helps
to maintain optimum host to fabric connections. In
addition to the GUI interface, management functions
can also be performed via a scriptable Command Line
Interface (CLI) as well as a web browser. With in-band
and out-of-band management capabilities, Emulex
provides data center administrators with the greatest
level of management flexibility.
· OneCommand Manager supports role-based
management to facilitate administration of adapters
throughout the data center without compromising
security. Management privileges can be assigned
based on LDAP and AD group memberships.
· Emulex’s management instrumentation complies
to Open Management Standards, such as SMI-S and
common HBA API support, which enables seamless
upward integration into enterprise storage and
server management solutions.
SPECIFICATIOnS
13-1200 · 6/13
LightPulse ®
LPe12000/LPe12002
8Gb Fibre Channel PCIe 2.0 Host Bus Adapter