Epson RX-8581JE - Manual (Page 27)

RX - 8581 SA
/
JE
/
NB
Page - 24 MQ372-02
8.6.6. I
2
C bus protocol
In the following sequence descriptions, it is assumed that the CPU is the master and the RX-8581 is the slave.
a. Address specification write sequence
Since the RX-8581 includes an address auto increment function, once the initial address has been specified,
the RX-8581 increments (by one byte) the receive address each time data is transferred.
(1) CPU transfers start condition [S].
(2) CPU transmits the RX-8581's slave address with the R/W bit set to write mode.
(3) Check for ACK signal from RX-8581.
(4) CPU transmits write address to RX-8581.
(5) Check for ACK signal from RX-8581.
(6) CPU transfers write data to the address specified at (4) above.
(7) Check for ACK signal from RX-8581.
(8) Repeat (6) and (7) if necessary. Addresses are automatically incremented.
(9) CPU transfers stop condition [P].
S
(1)
0
R/W
0
(3)
Address
(4)
0
(5)
0 Data
(8)
P
(9)
ACK signal from RX-8581
Data
(6)
0
(7) (2)
Slave address
b. Address specification read sequence
After using write mode to write the address to be read, set read mode to read the actual data.
(1) CPU transfers start condition [S].
(2) CPU transmits the RX-8581's slave address with the R/W bit set to write mode.
(3) Check for ACK signal from RX-8581.
(4) CPU transfers address for reading from 8581.
(5) Check for ACK signal from RX-8581.
(6) CPU transfers RESTART condition [Sr] (in which case, CPU does not transfer a STOP condition [P]).
(7) CPU transfers RX-8581's slave address with the R/W bit set to read mode.
(8) Check for ACK signal from RX-8581 (from this point on, the CPU is the receiver and the RX-8581 is
the transmitter).
(9) Data from address specified at (4) above is output by the RX-8581.
(10) CPU transfers ACK signal to RX-8581.
(11) Repeat (9) and (10) if necessary. Read addresses are automatically incremented.
(12) CPU transfers ACK signal for "1".
(13) CPU transfers stop condition [P].
S
(1)
0
R/W
0
(3)
Address
(4)
Sr
(6)
0
(5)
1
R/W
0
(8)
Data
(9)
0
(10)
Data
(11)
P
(13)
1
(12)
ACK from RX-8581 ACK from CPU
(7)
Slave address
(2)
Slave address
c. Read sequence when address is not specified
Once read mode has been initially set, data can be read immediately. In such cases, the address for each read
operation is the previously accessed address + 1.
(1) CPU transfers start condition [S].
(2) CPU transmits the RX-8581's slave address with the R/W bit set to read mode.
(3) Check for ACK signal from RX-8581 (from this point on, the CPU is the receiver and the RX-8581 is the
transmitter).
(4) Data is output from the RX-8581 to the address following the end of the previously accessed address.
(5) CPU transfers ACK signal to RX-8581.
(6) Repeat (4) and (5) if necessary. Read addresses are automatically incremented in the RX-8581.
(7) CPU transfers ACK signal for "1".
(8) CPU transfers stop condition [P].
S
(1)
1
R/W
0
(3)
Data
(4)
0
(5)
1
(7)
Data
(6)
P
(8)
ACK from CPU ACK from RX-8581
(2)
Slave address