Extron electronic Extron IPL T SFI244 - Manual (Page 2)

Serial Ports
Both models provide two serial ports for control of two independent serial
devices. The IPL T SF24 offers flexible connectivity via either 9-pin D-sub ports
for RS-232, RS-422, or RS-485 devices or captive screw ports (RS-232 only).
The IPL T SFI244 offers RS-232 connectivity (only) on captive screw ports.
When configured for pass-through mode, the interfaces can pass through
commands from an existing control system and also control and monitor
attached devices.
Flex I/O Ports
The IPL T SF24 and IPL T SFI244 each have four Flex I/O ports. These flexible
ports can be configured as analog in, digital in, or digital out. They support
digital and analog signals from 0 to 24 volts, allowing a wide variety of devices
to be controlled or monitored.
The 0 to 24 volt incoming analog signals are sampled with 12-bit precision.
Voltage thresholds can be set. When a threshold is passed, the IPL T SF24 or
IPL T SFI244 can be configured to send out a serial command, an e-mail, or
trigger another event. As an example, a thermal sensor installed in an
equipment rack can be connected to one of the Flex I/O ports. The
IPL T SF24 or IPL T SFI244 can be configured to send an e-mail if the rack
temperature exceeds a specific temperature.
When configured as digital inputs, the Flex I/O ports can connect to switches,
motion sensors, moisture sensors, and tally feedback. This provides the ability
to receive status from a variety of devices including projector lifts, motorized
projection screens, room partition switches, and push buttons.
When configured as digital outputs, the Flex I/O ports can drive LEDs,
incandescent lamps, or other devices. For applications that require contact
closure control, the Flex I/O ports can interface with an Extron IPA T RLY4, an
IP Link accessory featuring four isolated relays.
IR Ports
The IPL T SFI244 includes four fully programmable IR ports. Each IR port can
output IR signals with or without the carrier signal using an optional wired IR
emitter or IR broadcaster. IR control data can be collected and stored in two
ways: IR data file download and IR learning. Extron maintains a large library of
IR data files that can be downloaded from our Web site (www.extron.com) for
storage in the IPL T SFI244. The IPL T SFI244 will power four IR emitters; each
can be located up to 400 feet away.
IR Learning
The IPL T SFI244 has the ability to learn IR commands for virtually any IR
controllable device. The Extron IR Learner software, on intuitive PC-based
application for assisting with IR learning and managing IR data files, is available
at no charge and can be downloaded from the Extron Web site.
The Extron IPL T SF24 and IPL T SFI244 are part of the IP Link™ family of
ethernet control interfaces which are designed to integrate Internet Protocol
(IP) connectivity into A/V systems. Projectors, plasma displays, switchers, A/V
sources, lights, drapes, and many other devices can now be added to an
existing computer network, enabling asset management and remote
monitoring.
The Extron IPL T SF24 is a compact Ethernet control interface with integral
Web server, two serial ports, and four Flex I/O ports.
The Extron IPL T SFI244 is a compact Ethernet control interface with integral
Web server, two serial ports, four Flex I/O ports, four IR ports, and an IR learner.
S
PECIFICATIONS
D
ESCRIPTION
SERIAL CONTROL INTERFACE
Port number/type
IPL T SF24.............................. 2 RS-232/RS-422/RS-485
configurable serial
IPL T SFI244 .......................... 2 RS-232 only
Connectors
IPL T SF24.............................. (2) 9-pin male D and (1) 3.5 mm
5-pole captive screw connector
IPL T SFI244 .......................... (1) 3.5 mm 5-pole captive screw
connector
Baud rate and protocol .............. 300 to 115200 baud
Default settings (adjustable): 9600,
8-bit, 1 stop bit, no parity
Pin configurations
Serial, 9-pin D
RS-232 (default)................ 2 = RX, 3 = TX, 5 = GND, 7 = RTS,
8 = CTS
RS-422 .............................. 2 = RX-, 3 = TX-, 5 = GND,
7 = TX+, 8 = RX+
RS-485................................ 2&3 = data- and tie 2&3,
5 = GND, 7&8 = data+ and tie 7&8
Serial, 5-pole captive screw.... COM1: pin 1 = TX, 2 = RX, 3 = GND
COM2: pin 4 = TX, 5 = RX, 3 = GND
Program control ............................ Extron’s Simple Instruction
Set ™ – SIS ™
Global Viewer requirements .......... Microsoft ® Internet Explorer ver. 6
or higher or Netscape ® Navigator
ver. 7 or higher
ETHERNET CONTROL INTERFACE
Connectors ................................ 1 RJ-45 male connector
Data rate .................................. 10/100Base-T, half/full duplex with
autodetect
Protocols .................................. ARP, DHCP, ICMP (ping), TCP/IP,
Telnet, HTTP, SMTP
Default settings .......................... Link speed and duplex
level = autodetected
IP address = 192.168.254.254,
subnet mask = 255.255.0.0,
default gateway = 0.0.0.0
DHCP = off
FLEX I/O CONTROL INTERFACE
Number/type ............................ 4 analog or digital (configurable)
Connectors ................................ (1) 3.5 mm captive screw
connector, 5-pole captive screw
connector
Digital inputs
Input voltage range .............. 0-24VDC, clamped at +30VDC
Input impedance .................. 28 kohms
Programmable pullup ............ 2 kohms to +5VDC
Threshold low to high............ Programmable range: 100 mV to
24VDC, default = 2VDC
Threshold high to low............ Programmable range: 100 mV to
24VDC, default = 1VDC
Digital outputs .......................... 250 mA sink from 24VDC max.
Analog inputs ............................ 12 bit A/D, 0 to 24VDC
Pin configurations ...................... 1, 2, 3, 4 = digital I/Os 1, 2, 3, 4;
5 = GND
IR/SERIAL (IR/S) CONTROL INTERFACE — IPL T SFI244 ONLY
Output number.......................... 4
Connectors ................................ (1) 3.5 mm 8-pole captive screw
connector
IR output carrier frequency ........ 30 kHz to 1 MHz
Pin configurations ...................... pins 1, 3, 5, 7 = S1, S2, S3, S4
pins 2, 4, 6, 8 = GND
GENERAL
Power ........................................ 100VAC to 240VAC, 50/60 Hz,
10 watts, external, autoswitchable;
to 12VDC, 1 A power supply.
Product requires 0.5 A.
Temperature/humidity................ Storage -40° to +158°F
(-40° to +70°C) / 10% to 90%,
non-condensing Operating +32° to
+122°F (0° to +50°C) / 10% to
90%, non-condensing
Rack mount ................................ Yes, with optional 1U rack shelf,
part #60-190-01, or the
VersaTools
® rack shelf,
part #60-190-20; also under-
furniture mountable with optional
brackets #70-212-01or projector
mountable with optional brackets
#70-217-01
Enclosure type ............................ Metal
Enclosure dimensions ................ 1.7" H x 4.3" W x 3.0" D (1U high,
quarter rack width) 4.3 cm H x
10.9 cm W x 7.6 cm D (Depth
excludes connectors.)
Product weight .......................... 0.7 lbs (0.3 kg)
Shipping weight ........................ 2 lbs (1 kg)
Vibration .................................... ISTA/NSTA 1A in carton
(International Safe Transit
Association)
Listings ...................................... UL, CUL
Compliances .............................. CE, FCC Class A, VCCI, AS/NZS,
ICES
MTBF.......................................... 30,000 hours
Warranty .................................... 3 years parts and labor
Model Part Numbers
IPL T SF24 .................................. 60-544-02
IPL T SFI244 .............................. 60-544-06
Optional Accessories
1U 19" VersaTools rack shelf kit .. 60-190-20
1U 19" rack shelf kit .................. 60-190-01
Under desk mount...................... 70-212-01
Projector mount kit .................... 70-217-01
Specifications are subject to change without notice.
■ Bi-directional serial ports – Both models provide two serial ports
for control of two independent serial devices. When configured
for pass-through mode, the interfaces can pass through
commands from an existing control system and also control and
monitor attached devices.
■ Four Flex I/O ports – The Flex I/O ports can be configured as
either inputs or outputs and can interface with devices such as
relays, LEDs, and switches. The ports can also be configured to
receive analog voltages for use with photo sensors, level
feedback, and more.
■ IR learning capability – The IPL T SFI244 can be configured to
learn IR codes from a device's IR remote, enabling Web-based
control of many popular A/V devices via the network.
■ Global compatibility – All IP Link products use industry standard
Ethernet communication protocols, including ARP, DHCP, ICMP
(ping), TCP/IP, Telnet, HTTP, and SMTP.
■ Integral Web server – Each IP Link interface features a built-in
Web server with 1.25 MB of flash memory for storing the Global
Viewer management application and any user customized web
pages.
■ High performance architecture – Web pages are served many
times faster (6 Mbit/sec transfer rate) than similar products, so
data is refreshed at a consistently high speed.
■ Multi-user support – Each IP Link device supports multiple
concurrent users, improving system throughput by sending
information in parallel.
■ Multiple levels of security with password protection – User
access level authorizes limited entry to only pre-designated
functions, while administrator access level permits full access to
advanced settings.
■ Real-time clock – Programmable operating alerts, sequencing,
and automatic monitoring with the internal real-time clock and
calendar allow IP Link interfaces to routinely check a connected
device.
■ Intuitive configuration utility – The Global Viewer Configurator,
a Windows
® based program makes product setup simple and
easy. Based on information provided by the user, the Global
Viewer Configurator creates all of the files needed to build the
Global Viewer Web-based asset management application and
uploads them to the interface; no HTML programming
knowledge is required.
■ Extensive library of downloadable device drivers – Drivers for a
wide variety of projectors, A/V devices and Extron products are
available for download from the Extron Web site
(www.extron.com).
■ Global Viewer Web-based asset management application –
The Extron Global Viewer software is the free Web-based asset
management and control application designed specifically for
IP Link network interfaces. The Global Viewer enables asset
management functions including proactive maintenance, event
scheduling, remote technical support, and theft alerts.
F
EATURES
IPL T SFI244
Control Screen
Remotely control basic functions such
as power, volume, and inputs.
Monitor Screen
Remotely monitor power and
projector lamp hours.
Schedule Screen
Conveniently schedule
troubleshooting, automatic
monitoring, or system power.
Intuitive interface makes
operations easier.
Web pages can be customized
and tailored to meet customer
needs and facilitate
functionality.
Centralize management of
all A/V equipment in the
building or all over the
world.
Example of screen to control a matrix switcher.
Example of screen to control an Extron
CrossPoint matrix switcher.
IPL T SF24
IPL T SF24 4
IPL T SFI244 4
0
4
(2) RS-232/RS-422/RS-485
(2) RS-232
Model Serial Ports
Flex I/O
Ports
IR Ports