Euro-Pro X VPW42H - Manual (Page 4)

SAFETY & WARNING INSTRUCTIONS OPERATING INSTRUCTIONS
Maintenance & Cleaning Winterizing & Long Term Storage
WARNING
WARNING
When using the pressure cleaner, use
safety equipment including protective
clothing and safety goggles.
WARNING
Do not use acids, solvents, or any other
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
WARNING
• Never use the pressure cleaner to
draw in water contaminated with
solvents, e.g. paint thinners,
gasoline, oil, etc.
• Always prevent debris from being
drawn into the unit by suing a clean
water source.
• Always grip the gun firmly before
pressing the trigger, to counteract the
recoil when starting.
• Always discharge residual pressure
before disconnecting the hose.
• To ensure the appliance safety, use
only original spare parts from the
manufacturer, or approved by the
manufacturer.
• Always hold the trigger and lance
with two hands and keep a tight grip.
• Always keep the filter clean. If you
are in a high mineral area, check with
the water supply company whether
you should use additional filters
before using the pressure cleaner.
DANGER
EXTENSION CORDS
If using an extension cord, use only
grounded, three wire extension cords that
are in good condition. Use only extension
cords that are intended for outdoor use.
These extension cords are identified by a
marking "Acceptable for use with outdoor
appliances; store indoors while not in
use." use only extension cords having an
electrical rating not less than the product.
Do not use damages extension cords.
Examine extension cord before using and
replace if damaged. Do not abuse
extension cord and do not pull on the
cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect
from the receptacle before disconnecting
the product from the extension cord.
Note: Do not use 16 or 18 AWG
extension cords on this product.
DANGER
Failure to follow these instructions can
result in serious injury, including death.
WARNING
To reduce the risk of electrocution, keep
all connections dry and off the ground. Do
not touch the plug with wet hands.
Allowable Length
Extension Cord
25 ' 50 ’
14 AWG YES NO
12 AWG YES YES
Lubrication: The pressure washer is
supplied with a closed lubrication system,
so no addition of oil is needed.
Checking the Water Intake Filter: The
water intake filter is located inside the water
intake connector. (Fig. 10). Remove
periodically and inspect for any deposits
that might accumulate there.
1. Disconnect all water connections.
2. Turn the pressure washer on for a
few seconds, until any remaining
water in the pump exits.
3. Turn the unit off immediately.
4. Store the pressure washer, parts and
accessories in an area with a
temperature above 32°F.
Motor Thermostat
Important:
This pressure washer is
equipped with a motor thermostat. The
motor will stop if it is overheating. Wait
20-30 minutes before starting the unit
again. If it stops again, please call
customer service at 1 (800) 798-7398.
Fig. 10
Hose Connector
Water Intake
Cleaning the Nozzles: If you notice that the
output pressure fluctuates, you may have to
clean the nozzles. Turn the unit "Off". Unplug
from electric outlet and disconnect the water
supply. Remove the lances, trigger gun and
hose from unit. Take the small metal pin
provided and insert into the nozzle end to
remove any obstructions. (Fig. 11)
Fig. 11
This will occur more frequently if your
water supply is very hard.
Ground Fault Circuit Interrupter
(GFCI)
This unit is equipped with a Ground
Fault Circuit Interrupter (GFCI) built into
the plug. This device provides additional
protection from the risk of electrical
shock. When connecting the GFCI to the
electrical outlet, the indicator should
appear red. If the indicator is not red,
depress the RESET button on the GFCI
until the indicator appears red.
Cleaning Tips
Wood Decks: Rinse deck and
surrounding area with fresh water. If
using detergent, fill the detergent
applicator bottle and apply to the area
being cleaned. For optimal results,
reduce your work area to small sections
and clean each section one at a time.
Allow the detergent to rest on the surface
for a few minutes and then rinse at high
pressure. Do not let the detergent dry on
the deck. Always clean from left to right
and top to bottom for best results. Rinse
at high pressure using the fan jet keeping
the tip of the spray nozzle 8-12 inches
from the surface. Caution: For soft
woods, increase the distance from the
cleaning surface.
Cars, Boats, & Motorcycles: Wet down
area to be cleaned before applying
detergent with clean water. Fill the
detergent applicator bottle and apply to
the area being cleaned. To achieve best
results, clean one side at a time. Allow
the detergent to rest on the surface for a
few minutes but do not let it dry. Rinse at
high pressure using the fan jet in a
sweeping motion keeping the tip of the
spray nozzle at least 8-10 inches away
from the surface. Maintain a further
distance when using a direct spray. Wipe
surface for a polished finish.
Storing Your Pressure Washer
When you have finished using your
pressure washer, follow these steps for safe
storage:
1. Turn the pressure washer to the "Off"
position.
2. Turn off the water supply.
3. Before disconnecting the high pressure
hose connection, point the trigger gun in
a safe direction away from you and
discharge the high pressure water.
Disconnect the high pressure hose from
the pressure washer and trigger gun.
4. Disconnect garden hose from pressure
washer.
5. Remove excess water from the pump by
tipping the unit on both sides to drain
any remaining water from the water
intake and outlet fittings.
6. Drain detergent tank and flush with clean
water.
7. Wipe away any remaining water on all
parts and fittings.
8. Engage the trigger gun safety lock.
9. Store the unit and accessories in a room
above 32°F.
When an extension cable is required, you
must ensure that it has the right ampere
rating for your pressure cleaner and is in
safe electrical condition.
3 8