Euro-Pro NV30 - Manual (Page 15)

PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Cleaner W on’t
Run
1. Not properly plugged into wall
outlet.
2. No electricity in wall outlet.
3. On/Off switch not turned on.
4. Motor thermostat tripped.
1. Plug in firmly.
2. Reset circuit breaker or
replace fuse.
3. Push on/off switch to on
4. Reset motor thermostat.
Cleaner W on't
Pick Up
1. Full or clogged dust cup.
2. W rong carpet height setting.
3. Clogged air path.
4. Clogged hose.
5. Broken belt(s).
6. Telescopic wand not inserted
fully.
7. Dirty filters.
8. Debris screen needs
cleaning.
1. Clean dust cup.
2. Adjust setting.
3. Remove obstruction.
4. Remove obstruction.
5. Replace belt(s).
6. Push telescopic wand in
securely.
7. Clean / change filters
8. Clean debris screen.
Cleaner Picks
Up Moveable
Rugs Or Pushes
Too Hard
1. W rong carpet height setting. 1. Adjust setting.
Agitator Does
Not Turn
1. Broken belt(s).
2. Belt(s) installed incorrectly.
1. Replace belt(s).
2. Check belt changing.
Air Flow
Restricted W ith
Attachm ent Use
Sound Changes
1. Attachment use restricts air
flow.
2. New carpet debris clogging
air path.
1. Check attachment.
2. Remove obstruction.
14
Changing the Headlight
WARNING:
To reduce the risk of electric
shock, the power cord must be
disconnected before performing
maintenance/trouble shooting checks.
Occasionally the headlight will require
changing.
1. Turn the vacuum off and unplug from
the electrical outlet.
2. With a flathead screw driver, insert the
end of the screwdriver into the two
slots on top of the headlight lens and
gently pull down. (Fig. 59)
Fig. 59
Lens Slots
3. Lift out the headlight lens.
4. Remove the light bulb by pulling it out
carefully.
5. Replace the new bulb by pushing it in.
6. To replace the headlight lens, insert
the bottom tabs of the lens into the
holding slots and snap the top back
into place to secure.
TROUBLESHOOTING APPRENEZ À CONNAÎTRE VOTRE BALAYEUSE CYCLONIC
VERTICALE
Spécifications Techniques
Voltage : 120V, 60Hz.
Alimentation : 12 A
Remarque : * Les illustrations peuvent différer du produit exact.
33
14. Support du Tube Inférieur
15. Tuyau Super Extensible
16. Suceur Plat
17. Brosse à Meubles
18. Brosse à Épousseter
19. Bouton de Dégagement du Bac à
Poussière
20. Port de Rinçage du Collecteur
Cyclone
21. Support du Tube Supérieur
22. Support de Dégagement Rapide du
Cordon d’Alimentation
23. Dégagement du Tube Télescopique
24. Support du Cordon d’Alimentation
25. Bouton Marche/Arrêt
1. Poignée
2. Tube Télescopique
3. Poignée de Transport
4. Bouton de Dégagement de la
Porte Inférieure du Collecteur
Cyclone.
5. Collecteur Cyclone
6. Bac à Poussière
7. Écran de Débris
8. Lumière d’Indicateur du Filtre
9. Lumière
10. Bouton d’Ajustement de la
Hauteur du Tapis
11. Protège-Meuble
12. Déclencheur de Poignée
13. Sélecteur Tapis-à-Plancher