Elation Professional ELED STRIP RGBW - Manual (Page 4)

© Elation Lighting ® - www.elationlighting.com - ELED Strip RGBW Instruction Manual Page 8
ELED Strip RGBW Operating Instructions ELED Strip RGBW Operating Instructions
© Elation Lighting ® - www.elationlighting.com - ELED Strip RGBW Instruction Manual Page 7
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until 0010 is displayed, press the UP button to display 0020.
Now the display will disappear after 10s. Press any button to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds.
To set the display press the MODE button until 0010 is displayed. The
display will now stay on at all times.
0010= LCD display on at all times.
0020= LCD display shuts off after 10 seconds.
Operating Modes:
You can use the ELED Strip RGBW in five ways:
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
• Color mode - Select one of 32 colors to remain static
• Preset mode - There are 32 built in programs to choose from.
• RGBW mode - Control the intensity of all four colors adjusting the
intensity to your desire.
• Sound-Active mode - The unit will react to sound, chasing through the
built in programs.
Master-Slave Operation:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units built-in programs.
Any unit can act as a Master or as a Slave however, only one unit can be
programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR microphone cables to link your units together.
Remember that the Male XLR connector is the input and the Female
XLR connector is the ouput. The first unit in the chain (master) will
use the female XLR connector only. The last unit in the chain will use
the male XLR connector only.
You can also daisy chain the power cords, this can only be
done with 20 fixtures. After 20 you will need to use a new
power outlet. They must be the same fixtures. DO NOT mix
fixtures.
2. Set the “Master” unit to your desired mode or operation.
3. For the “Slave” unit(s), press the MODE button until the display to
shows “XXX7”.
4. Connect the “Slave” unit or units and they will automatically start to
follow the “Master.”
Color Mode:
1. Plug the fixture in and press the MODE button until “XXX8” is dis-
played.
2. There are 32 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons.
Preset Program Mode:
1. Plug the fixture in and press the MODE button until “XXX9” is dis-
played.
2. There are 20 programs to choose from. Select your desired program
by pressing the UP and DOWN buttons. You can set your program
speed by following the instructions below.
Preset Program Mode Adjustment:
1. To adjust the speed of your Preset mode program press the MODE
button until “XXX ” is displayed. “XXX ” is the next mode after Pre-
set Mode.
2. Press the UP or DOWN buttons to make the adjustmetns. Set to your
desire.
RGBW Mode:
1. Plug the fixture in and press the MODE button until:
2. When XXX is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When XXX is displayed you are in Green dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When XXX is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity.
4. When XXXE is displayed you are in White dimming mode. Press the
UP and DOWN buttons to adjust intensity.
Sound Active Mode:
In this mode the ELED Strip RGBW will react to sound, and chase
through the different programs.
1. Plug the fixture in and press the MODE button until “XXX ” is dis-