Euro-Pro SELECT EP724H - Manual (Page 6)

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
4. Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.
Small Air Driven Turbo Brush
Top Rim
Bottom Rim
1. Push the Power
On/Off button to
"Off" and
disconnect the
power cord from
the wall outlet.
2. Remove the
flexible hose.
3. Push the dust
cup cover release
button located
on the front
side of
the unit (see illustration) and lift
the cover up.
4. Hold the dust cup by the handle
and lift it up out of the vacuum .
5. Hold dust cup over a waste
basket (garbage can), lift cover
and then depress the trap door
release button to open the dust
cup. Dispose of the dust inside.
(See illustrations below.)
Note: If dust is tightly packed and
difficult to remove, tap the side of
the dust cup lightly against the
side of the waste basket (garbage
can).
6. To remove the
Rinseable "TapClean"
HEPA dust cup filter
from the dust cup,
hold the filter from
the tab at the top
of it and lift. See
illustration at right.
Warning: Always unplug the unit from
electrical outlet before removing the Dust
Cup (container).
Warning : After each Use - Always
remove the Rinseable "TapClean" HEPA
Filter from the Dust Cup, then vigorously
“TapClean” HEPA Filter until no more
dust can be removed.
Important: When "TapCleaning" the
HEPA filter, hold the HEPA filter from the
top rim and tap ONLY the bottom rim
against the side of the waste container.
NEVER tap directly on the pleated folds of
the HEPA filter.
Lift cover, then depress button
to open trap door
8. Rinse the debris screen under the
faucet until clean. Allow to air dry or
dry with a clean dish towel. Do NOT
wash in dishwasher.
9. To replace the debris screen onto the
filter, slip the debris screen over the
filter and twist clockwise to lock in
place.
7. After you have removed the
Rinseable "TapClean" HEPA dust
cup filter from the dust cup, separate
the debris screen from the HEPA filter
cartridge by holding the top rim of the
filter and twisting the debris screen
counterclockwise to unlock the debris
screen from the filter. Then lift the
debris screen to remove.
Removing & Cleaning the
Rinseable "TapClean" HEPA
Dust Cup Filter
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
Note: Once all
attachments are
in place, unwind
a sufficient length
of cable and insert
the plug into the
wall outlet. A
yellow mark on the
power cord shows
the ideal cable length. Don't pull the
power cord beyond the red mark.
1. Insert the power plug into the wall
outlet. (Fig. 1)
2. Press the Power
On/Off button
located on the
unit to turn the
vacuum cleaner
"On".
3. To rewind the
power cord,
press the cord
rewind button with one hand and hold
the plug of the power cord with the
other hand to ensure that it does not
whip causing damage or injury.
(Fig. 2)
1. Crevice Tool with Brush
For radiators, crevices,
corners, baseboards and
between cushions.
2. Upholstery Brush
The dusting brush is used
for the furniture
Using your Vacuum
Fig. 1
Fig. 2
Crevice Tool and Dusting Brush
Turbine
Tilt
Upwards
Locking Latch
1. Slide locking latch forward then tilt the
top housing of the brush upwards. The
top housing is hinged and will tilt up
approximately 45° only.
2. Inspect turbine wheel and air passage
for debris and/or blockage. Remove
debris if present.
3. Inspect the rotating brush for built-up
hair or string. If present, remove by
carefully cutting with scissors. Avoid
damaging or cutting bristles.
Cleaning the Small Air Driven
Turbo Brush
The efficiency of your air driven turbo
brush depends on the bristle brush
rotating at high speed. Strong air suction
is needed to accomplish this. In order to
ensure that maximum air suction is
maintained, please read the following
instructions:
1. Empty the dust cup frequently.
2. Always shake out the dust cup filter
when emptying the dust cup container.
3. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
4. Keep Air Driven Turbo Brush turbine
free of dirt and foreign matter. (See
illustration for cleaning instructions.)
To use the small air driven turbo brush,
remove the chrome telescopic tube from
the hose and insert the end of the hose
into the turbo brush.
Motor Thermostat
IMPORTANT, Please Note : The
Rinseable “TapClean” HEPA Dust Cup
Filter will stop most of the tiniest dust
particles from re-entering the air you
breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!!
Because of this incredible filtration
performance, the HEPA Dust Cup Filter
will quickly accumulate dirt inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA Filter as described in this section,
then reconnect unit and proceed with
vacuuming.)
Important: This vacuum cleaner is
equipped with a motor protective
thermostat. If for some reason your
vacuum overheats, the thermostat will
automatically turn the unit off. Should this
occur, unplug the vacuum from the wall
outlet and turn off the switch. Empty the
dust cup, "TapClean" the dust cup filter
and check for blockages in hose and
suction inlet. Allow the unit to cool for a
minimum of 45 minimum prior to
restarting the unit. To restart, re-plug the
vacuum into the wall socket and turn the
switch back on
5 6