Save these instructions, Important safety instructions, For household use only – Euro-Pro SHARK EP470 User Manual

Page 3

Advertising
background image

TROUBLESHOOTING

IMPORTANT SAFETY INSTRUCTIONS

PROBLEM

POSSIBLE REASONS & SOLUTIONS

Iron does not heat

Thermostat ready light
goes On and Off

Some odor or small
particles come out of
steam vents of new
iron

Iron does not steam

Water droplets coming
from steam vents

• Iron should be plugged into a 120V AC electrical

outlet only.
Make sure that the plug is securely in the socket.

• Temperature setting too low.

Turn to higher setting.

• This is normal.

The light goes On and Off as the thermostat is
switching the heating element On and Off to
maintain the selected temperature.

• This is normal.

Follow instructions for first use and allow iron to steam
through 2-3 fillings & press the steam burst button
occasionally to eliminate small white particles.

• Water tank may be empty or water level is very low.

Add water.

• Make sure that the temperature control dial and

the variable steam control are correctly set. For
maximum steam, (setting ‘Max’ on steam control),
temperature control dial should be set on ‘•••’.

• Adjustable steam control is set on “0”.

Always allow the iron to reach the selected

temperature with the adjustable steam control setting

at ‘0’. Make sure the temperature control dial is set in
the correct steam area, e.g. ‘•’, and the steam control is
not on ‘0’. For more steam, turn temperature dial to
higher setting, e.g. ‘•••’, and the steam control to ‘Max’.

• If temperature setting and steam control setting are

correct and there is no steam, gently tap the
soleplate on the ironing board a few times. Move
the variable steam control from ‘0’ to ‘Max’ a few
times.

• Iron may not be hot enough. Set thermostat to the

‘Max’ position. Always allow iron sufficient time to
heat up (thermostat light goes off) before activating
the variable steam control.

• Overuse of steam burst. Allow more time between

each burst.

• Iron may have been overfilled. Turn iron off,empty

water and follow instructions for filling.

• Steam performance may be low if iron requires

seasoning. To season, use regular tap water for 1or 2
tanks until steam performance improves.

reassembly can cause the risk of
electric shock when the iron is used.

8. Close supervision is necessary for

any appliance being used by or near
children. Do not leave iron
unattended while connected or on an
ironing board.

9. Burns can occur from touching hot

metal parts, hot water or steam. Use
caution when you turn a steam iron
upside down; there may be hot
water in the reservoir.

10. This appliance is for household

use only.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not

operate another high-wattage
appliance on the same circuit.

2. If an extension cord is absolutely

necessary, use a 13-ampere cord.
Cords rated for less amperage may
overheat. Use care to arrange the
cord so that it cannot be pulled or
tripped over.

When using your iron, basic safety
precautions should always be followed,
including the following:
1. Read all instructions carefully.
2. Use iron only for its intended use.
3. To protect against risk of electrical

shock, do not immerse the iron in
water or other liquids. Always turn
the iron to “OFF” before plugging in
or unplugging from outlet.

4. Never yank cord to disconnect from

outlet. Grasp plug and pull to
disconnect.

5. Do not allow cord to touch hot

surfaces. Let iron cool completely
before putting away.

6. Always disconnect iron from

electrical outlet when filling with
water, emptying, or when not in use.

7. Do not operate iron with a damaged

cord, or after the iron has been
dropped or damaged in any manner.
To avoid the risk of electric shock,
do not disassemble the iron. Return
the iron to the nearest service facility
for examination and repair. Incorrect

POLARIZED PLUG

:

This appliance has a polarized plug (one blade is
wider than the other). As a safety feature, this plug
will fit into a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician. Do no attempt to defeat this safety
feature.

SAVE THESE INSTRUCTIONS

For Household Use Only

Rev. 00302

1

Printed in China

11

Advertising