Hotpoint OS 897D C IX - Manual (Page 9)

9
GB
Main Space
Starting the oven
1. Fit the DIVIDER to the DIVIDER shelf “D” using the
two pins, with the arrows turned towards the rear part
of the oven. After it has been fitted correctly, you will
be able to read the text “OPENSPACE” on the front
part of the DIVIDER frame. A buzzer will sound to
confirm that the DIVIDER has been fitted correctly; it
will then be possible to use the two Main and Small
space compartments separately or at the same time.
 The EXTRALARGE SPACE FUNCTION knob will be
disabled.
2. Select the desired cooking function by turning the
MAIN SPACE FUNCTION knob.
3. The oven will begin its preheating stage. The
temperature may be changed by turning the
TEMPERATURE knob. The indicator light flashes
during the pre-heating stage.
4. Once the pre-heating stage is completed, the
icon stops flashing (becomes fixed) and a buzzer
sounds. It is now possible to introduce foodstuffs into
the oven.
5. During cooking it is always possible to:
- Change the temperature by turning the
TEMPERATURE knob.
- Set the cooking duration in addition to the cooking
end time.
- Stop cooking by turning the MAIN SPACE FUNCTION
knob to the “0” position.
6. If a blackout occurs while the oven is already in
operation, an automatic system within the appliance
will reactivate the cooking function from the point at
which it was interrupted, as long as the temperature
has not dropped below a certain level. Programmed
cooking modes which have not started will not be
restored and must be reprogrammed.
Cooking functions
UNIVERSAL function
All heating elements and the fan are activated. Since
the heat remains constant throughout the oven, the air
cooks and browns food in a uniform manner. A
maximum of three racks may be used at the same time.
If you are using several racks at the same time, we
recommend you place the dripping pan on shelf level
1. If you are cooking on 3 levels at the same time, we
recommend you place the shelves on racks 3 and 5,
and the dripping pan on rack 1.
Using the Small Space and Main Space at
the same time
Starting the oven
1. Fit the DIVIDER to the DIVIDER shelf “D” using the
two pins, with the arrows turned towards the rear part
of the oven. After it has been fitted correctly, you will
be able to read the text “OPENSPACE” on the front
part of the DIVIDER frame. A buzzer will sound to
confirm that the DIVIDER has been fitted correctly; it
will then be possible to use the two Main and Small
space compartments separately or at the same time.
 The EXTRALARGE SPACE FUNCTION knob will be
disabled.
 In order to improve the oven’s energy efficiency, the
pre-heating time of the SMALL SPACE cavity lasts
about 15 minutes.
 If the MAIN SPACE is set at a temperature below
150°C, in order to safeguard the cooking results, the
grill function will not start: the display will visualise
“OFF.”
2. Select the desired cooking function for each recess
by turning the SMALL SPACE FUNCTION and/or MAIN
SPACE FUNCTION knobs. The icon indicates that
the Small Space has been selected and that it is
therefore possible to adjust the Small Space settings;
the icon lit up on the display indicates that the
Main Space has been selected and that it is therefore
possible to adjust the Main Space settings.
3. Both ovens will begin the preheating stage. The
temperature may be changed by turning the
TEMPERATURE knob. The indicator light flashes
during the pre-heating stage.
4. Once the pre-heating stage is completed, the
icon stops flashing (becomes fixed) and a buzzer
sounds. It is now possible to introduce foodstuffs into
the oven.
5. The digits on the display become brighter to
indicate which recess you are adjusting. To modify the
settings for the other recess, press the button. The
Small Space and Main Space settings may actually be
changed during simultaneous cooking:
- Change the cooking function by turning the SMALL
SPACE FUNCTION and/or MAIN SPACE FUNCTION
knob.
- Change the temperature by turning the
TEMPERATURE knob.
- Set the cooking duration in addition to the cooking
end time.
- Stop cooking by turning the SMALL SPACE
FUNCTION and/or MAIN SPACE FUNCTION knob to
the “0” position.