Husqvarna QN 4039 - Manual (Page 5)

QN 4021 / QN 4039
9
Description of the microwave oven
Turntable and turntable support
The turntable and turntable support
should be installed as shown in the dia-
gram. Take care to ensure the turntable
support is properly in place.
The turntable may turn clockwise or coun-
terclockwise during operation. Do not rotate
the turntable manually, as you could
damage the drive system.
Accessories
1 Cooking compartment
2 Viewing window
3 Oven door
4 Door catch
5 Safety interlock system
6 Control panel
7 Door open button
8 Drive shaft for turntable
QN 4021 / QN 4039
8
Installation
• When you unpack the oven, check
that the product is free from damage.
Damage or any missing parts must be
reported immediately to the retailer.
The oven, parts of the oven or the
accessories may be wrapped by a pro-
tection foil. If so, you must remove this
foil before using the oven. Do not leave
packing material so that small children
can play with it. This can be hazardous.
• Do not use your appliance immediately
(wait approx. 1-2 hours) after transfer
from a cold place to a warm place as
condensation may cause a malfunction.
• This oven can be used as a free stan-
ding oven or built-in using the kit avail-
able with the oven. To install the oven in
a kitchen cabinet follow the instructions
supplied with the building-in kit. The
oven should be in-stalled on a flat, level
surface at least 85 cm above floor level.
The surface must be strong enough to
safely bear the weight of the oven, and
the contents. To avoid the possibility of
causing vibration or noise, the oven must
be in a stable position.
• Be sure to install the oven away from
heat and water sources.
• Do not block air vents on the top and
the sides of the cabinet nor place any
articles on the top of the oven. A gap all
around the oven is necessary : 20 cm
above the oven and any objects, 5 cm
on the sides
and 10 cm
behind the
oven. If air
vents are
b l o c k e d
during ope-
ration, the oven may overheat, and this
may lead to malfunctioning.
• This oven does conform to EEC require-
ments* of radio interference suppression,
but some interference may occur if it is
placed too close to a radio or TV, so
keep them as far apart as possible.
• To install the appliance in a kitchen
cabinet, use the appropriate mounting
frame, kit number EBR/BF 517 or 617
for model QN 4021 or kit number
EBR/BF 624 for model QN 4039. When
building into a high cabinet, you may
use the liftdoor. Note the relevant infor-
mation for installation and connection
given in the operating instructions.
Attention ! Never operate the micro-
wave oven with the lift door closed.
Such operation would damage your
appliance and invalidate the guarantee.
Electical connections
• The oven is delivered with the power
cord and a plug for 230-240 V, 50Hz,
earthed socket outlet.
• Earth protection minimizes the risks
should a short-circuit occur. Check to
ensure the voltage of the oven matches
the supply. N.B. If the oven is connected
to the socket via an extension cord,
make sure the cord is earthed.
This appliance must not be used on a
non-earth protected power supply.
Contact an electrician if you are uncertain
regarding electrical connection of the
oven or provision of earth protection of
the supply.
• Microwave power output :
QN 4021 - 750W / QN 4039 - 900W
• This appliance complies with E.E.C.
directive No. 87/308 of 2.6.87 relative to
radio interference suppression.
Built-in model
5 cm
20 cm
10 cm
5 cm