Home Automation 38A00-3 - Manual (Page 3)

HAI UPB™ LUMINA MODE CONTROLLER OPERATION
Although the HAI UPB™ Lumina Mode Controller will perform differently once it is configured by the Lumina controller, the
following describes the operation of the HAI UPB™ Lumina Mode Controller in its factory default configuration.
The HAI UPB™ Lumina Mode Controller has six pushbuttons labeled AWAY, HOME, SLEEP, VAC, SPCL, and PARTY, which
(by factory default) are used to control six lighting scenes. When the pushbutton labeled “AWAY” is pressed, the LED behind the
“AWAY” pushbutton is illuminated and any other is turned off. When the pushbutton labeled “HOME” is pressed, the LED behind
the “HOME” pushbutton is illuminated and any other is turned off. When one of the pushbuttons labeled “SLEEP”, “VAC”, “SPCL”,
or “PARTY” is pressed, the LED behind the respective pushbutton is illuminated and any other is turned off. No more than one
pushbutton is illuminated at a time.
Pushbutton Operation
In its factory default configuration, the “AWAY” pushbutton will brighten the UPB™ Wall Switch Dimmers to 100% at each switch’s
default fade rate when pressed. When the “AWAY” pushbutton is double-tapped, the UPB™ Wall Switch Dimmers will snap to
100%. When pressed or double-tapped, the “AWAY” pushbutton will illuminate and any others are turned off. The “AWAY”
pushbutton is also used to brighten the last lighting scene that was turned on. When the “AWAY” pushbutton is pressed and held
down, the UPB™ Wall Switch Dimmers will slowly brighten, and then stop brightening when the “AWAY” pushbutton is released.
In its factory default configuration, the “HOME” pushbutton will fade the UPB™ Wall Switch Dimmers to 0% (off) at each switch’s
default fade rate when pressed. When the “HOME” pushbutton is double-tapped, the UPB™ Wall Switch Dimmers will snap to 0%.
When pressed or double-tapped, the “HOME” pushbutton will illuminate and any others are turned off. The “HOME” pushbutton is
also used to dim the last lighting scene that was turned on. When the “HOME” pushbutton is pressed and held down, the UPB™ Wall
Switch Dimmers will slowly dim, and then stop dimming when the “HOME” button is released.
In its factory default configuration, the “SLEEP” pushbutton will brighten the UPB™ Wall Switch Dimmers to 80% at each switch’s
default fade rate when pressed or double-tapped. When pressed, the “SLEEP” pushbutton will illuminate and any others are turned
off.
In its factory default configuration, the “VAC” pushbutton will brighten the UPB™ Wall Switch Dimmers to 60% at each switch’s
default fade rate when pressed or double-tapped. When pressed, the “VAC” pushbutton will illuminate and any others are turned off.
In its factory default configuration, the “SPCL” pushbutton will brighten the UPB™ Wall Switch Dimmers to 40% at each switch’s
default fade rate when pressed or double-tapped. When pressed, the “SPCL” pushbutton will illuminate and any others are turned off.
In its factory default configuration, the “PARTY” pushbutton will brighten the UPB™ Wall Switch Dimmers to 20% at each switch’s
default fade rate when pressed or double-tapped. When pressed, the “PARTY” pushbutton will illuminate and any others are turned
off.
CONFIGURING THE HAI UPB™ LUMINA MODE CONTROLLER
The HAI UPB™ Lumina Mode Controller is designed to set the mode in a Lumina system, but also has several configuration options:
Option Factory Default CONFIGURED AS LUMINA MODE CONTROLLER
“AWAY” Pushbutton On Button / Link 001 Sets the Lumina mode to Away.
“HOME” Pushbutton Off Button / Link 002 Sets the Lumina mode to Home.
“SLEEP”, “VAC”, “SPCL”,
and “PARTY” Pushbutton Scene Activator / Links 003,
004, 005, 006 – respectively Sets the Lumina mode to Sleep, Vacation, Special, and Party,
respectively.
“AWAY”, “HOME”, “SLEEP”,
“VAC”, “SPCL”, and
“PARTY” LED Indicators Each LED Indicator is assigned
to its pushbutton’s Link ID
Each LED Indicator is mutually
exclusive (only one LED is on
at a time). When the Lumina mode is changed, the LED indicator behind
the respective pushbutton is illuminated and any other is turned
off.
UPB Transmission Attempts 2 No change
UPB ID NID = 255
UID = 080 The Lumina controller configures Network ID (NID), Unit ID
(UID), Network Password, Network Name, Room Name,
Device Name, etc.
LED Brightness High No change.
LED Backlighting Enabled No change.