Harman-Kardon DMC 1000 - Manual (Page 8)

8 FRONT PANEL CONTROLS
IMPORTANT NOTE: The DMC 1000’s front-
panel controls use advanced touch-sensitive
technology. To use the front panel, place a finger
over any of the illuminated icons. A gentle tap is
all that is necessary. Wait a few seconds for the
DMC 1000 to process each command. To
remove fingerprints, wipe the front panel with a
dry microfiber cloth.
Power: When the DMC 1000 is connected to
an AC power source and the rear-panel Master
Power Switch is on, this control will indicate one
of four power states:
• Full-Off Mode (dim blue) – The DMC
1000, including its hard-disc drive, is fully
powered down.
• Sleep (Standby) Mode (amber) – The
DMC 1000 will not respond to any commands
other than to power on.
• Server Mode (amber) – The DMC 1000
may be controlled via the RS-232 Port or the
Network Connection, but the on-screen menu
system is off.
• Full-Power Mode (bright blue) – The DMC
1000 operates normally.
The description of each mode and the DMC
1000’s response to the power controls is shown
in Table A7 in the Appendix.
0 Main Information Display: This display
delivers messages and status indications to help
you operate the DMC 1000 player.
1 Power On/Off (Standby): Press the button
once to turn the DMC 1000 player on, press it
again to put the unit in the Standby mode.
2 Open/Close: Press this button to open or
close the Disc Tray.
3 Disc Drawer.
4 Play/Pause: Press to initiate playback or to
resume playback after Pause has been pressed.
Press this button to momentarily pause play-
back. To resume playback, press the button
again. If a DVD is playing, action will freeze and
a still picture will be displayed when the button
is pressed.
5 Stop: Press this button once to place the
disc in the Resume mode, which means that
playback will stop, but as long as the tray is not
opened or the disc changed, DVD playback will
continue from the same point on the disc when
the Play Button is pressed again. Resume will
also work if the unit was turned off. To stop a
disc and have play start from the beginning,
press the button twice.
6 Skip/Search (Previous): Press this button
to move backward through the music tracks on
a CD disc or the chapters on a DVD disc. Keep
the button pressed to search backwards at one
of the available speeds. 7 Skip/Search (Next): Press to move forward
through the music tracks on a CD or the
chapters on a DVD disc. Keep the button pressed
to search forwards at one of the available
speeds.
8 Record: When an audio CD is loaded, or the
Analog Audio Inputs are selected as the source,
press this button to view the Record tab of the
on-screen menu. Pressing this button does not
begin the recording.
NOTE: It is not possible to record from one of
the memory cards or the USB device to any
other media or to the USB device. It is also not
possible to transfer image or video files.
However, an audio signal is always available at
the Analog Audio Outputs. You may make ana-
log recordings from any source by connecting an
analog audio recorder to the rear-panel Analog
Audio Outputs.
9 Menu: Press to activate the on-screen
menu system, or to navigate back up one level
in the menu system.
NOTE: It is not possible to select a new source
while the current source is playing or even while
it is paused. Press the Stop Button before select-
ing a new source.
0 Main Information Display
1 Power On/Off (Standby)
2 Open/Close
3 Disc Drawer
4 Play/Pause
5 Stop 6 Skip/Search (Previous)
7 Skip/Search (Next)
8 Record
9 Menu
A Navigation Buttons
B Front Panel Door C Card Slot 1
D Card Slot 2
E USB Port
F Remote IR Sensor
1
3
8 7 6 5 4 9 A B A
2 0 E D C F
1 4 5 6 7 8 2 A 9
3 B 0 D C E F
Front Panel Controls
2083124_HK_DMC_1000_OM_ENG.qxp:34241_DMC250_ENG 15/08/08 10:49 Side 8