Hunter Fan CARE FREE 33283 - Manual (Page 3)

©2008 HUNTER FAN CO. 43050-01 06/04/08 3
HumIdIfIEr Parts
figure 1
base
Permawick™
filter
Permawick™
filter frame
tank
Cap
main
Housing
Power/speed
Control
Humidistat
Controls
water
tank
Easy tote
Handle
Adjustable Humidistat: Enables you to set a desired
maximum humidity level. Once this level is reached, the unit will
shut off until the humidity level drops.
NOTE: The humidifier may not be running because the
humidistat setting may need to be adjusted.
Power/Speed Control: Turns the humidifier ‘ON’ and ‘OFF’.
The power should always be off before unplugging the
humidifier, moving the humidifier, or refilling the water tank.
Power Light: The light will be illuminated when the power is
on.There are 2 fan speeds, high and low.
NiteGlo™ Night Light Control: Turns the night light ‘ON’ and
‘OFF’. The night light can be turned on even if the humidifier
fan is turned off.
HumIdIfIEr fEaturEs
figure 2
Power
light
Power/speed
Control
adjustable
Humidistat
Control
niteGlo™
night
light
Control
1. Remove The Care Free® Evaporative Humidifier from its
packaging. Read and Save the Instructions.
2. Place the humidifier on a hard, flat, water resistant surface.
Always place the humidifier at least six (6) inches away from
walls and sources of heat.
3. Lift the main housing to confirm that the PermaWick™ filters
are placed upright in the slots. Replace the main housing.
(See Figure 1.)
4. Remove the water tank and take it to the sink or tub to fill.
5. Turn the tank upside down and unscrew the tank cap by
turning it counterclockwise. Fill the water tank with cool water
and replace the tank cap (Never use hot water). Be sure not
to fill the tank to overflowing as water damage may occur to
furniture or flooring due to spillage.
HUNTER WILL NOT ACCEPT RESPONSIBILITY FOR
DAMAGE TO PROPERTY CAUSED BY WATER SPILLAGE.
6. Carry the tank back to the humidifier. Turn the tank upright
and place the full tank on the unit and allow the water to fill
the bottom tray. Be sure that the tank is seated properly in
the base. If the tank is properly located on the base, you will
see air bubbles flowing up into the tank.
7. With the power control knob in the ‘OFF’ position, plug the
humidifier into the wall.
CAUTION: Never plug in the Humidifier while your hands are
wet as Electric Shock could occur.
8. Once the water is at the proper level, the tank will stop
bubbling. Run the unit on “HI” speed for 11⁄2 minutes for
optimum pump operation. Set the unit to the desired speed.
9. You can choose the desired humidity output by adjusting
the Adjustable Humidistat knob. In a very dry room, the “HI”
setting should be used to quickly achieve a comfortable
level of humidity. Once the room is comfortable, you can
turn the Adjustable Humidistat down. Selection of your
desired humidity level is a personal choice and you may
have to adjust the dial to find the level where you feel most
comfortable. To begin with, we suggest you try a middle
location between the lowest and the maximum setting. Then,
adjust the level to suit your needs.
10. When the humidity reaches the level you have set, the
Humidifier will shut off. The humidifier will not output
humidity while the humidity in the room is at the selected
humidity level. When the humidity in the room drops below
the selected level, the humidifier will cycle on again.
11. Follow REFILLING THE WATER TANK directions.
12. Use the control button to turn the night light off and on.
The night light can be operated even if the humidifier fan is
turned ‘OFF’.
using your Humidifier