Homelite CSP3816 - UT74123D - Manual (Page 9)

UK - Page 9
OPERATION
KICK-BACK PRECAUTIONS
See Figures 4 and 5.
Rotational kick-back (A) occurs when the moving chain contacts
an object at the Kick-back Danger Zone (B) of the guide bar.
The result is a lightning-fast, reverse reaction which kicks the
guide bar up and back towards the operator. This reaction can
cause loss of control which may result in serious injury.
FUEL AND REFUELLING
HANDLING THE FUEL SAFELY
WARNING:
KICK-BACK occurs when the moving chain contacts an
object at the upper portion of the tip of the guide bar or
when the wood closes in and pinches the saw chain in
the cut. Contact at the upper portion of the tip of the guide
bar may cause the chain to dig into the object and stop the
chain for an instant. The result is a lightning-fast, reverse
reaction which kicks the guide bar up and back towards the
operator. If the saw chain is pinched along the top of the
guide bar, the guide bar can be driven rapidly back toward
the operator. Either of these reactions may cause you to
lose control of the saw, which could result in serious injury.
Do not rely exclusively upon the safety devices built into
your saw. As a chainsaw user, you should take several
steps to keep your cutting jobs free from accident or injury.
WARNING:
Always turn off engine before refuelling. Never add fuel to
a machine with a running or hot engine. Move at least
15 m (50 ft.) from refuelling site before starting the engine.
DO NOT SMOKE! Failure to heed this warning can result
in possible personal injury.
■ ■ ■ ■ ■ Always handle fuel with care: it is highly flammable.
■
■ ■ ■ ■ Always refuel outdoors and do not inhale fuel vapour.
■
■ ■ ■ ■ Do not let petrol or oil come in contact with skin.
■
■ ■ ■ ■ Keep petrol and oil away from the eyes. If petrol or oil comes
in contact with the eyes, wash them immediately with clean
water. If irritation is still present, see a doctor immediately.
■ ■ ■ ■ ■ Clean up spilled fuel immediately.
WARNING:
Check for fuel leaks. If any are found, correct them before
using the saw to prevent fire or burn injury.
}
50:1
FILLING THE TANK
See Figure 6.
Refer to “Specific Safety Rules – Refuelling” earlier in this
manual for additional safety information.
1. Clean the surface around fuel cap to prevent contamination.
2. Loosen the fuel cap slowly.
3. Carefully pour the fuel mixture into the tank. Avoid spillage.
4. Prior to replacing the fuel cap, clean and inspect the gasket.
5. Immediately replace the fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for the engine to emit smoke during and
after the first use.
MIXING THE FUEL
■ ■ ■ ■ ■ This product is powered by a 2-cycle engine and requires
pre-mixing petrol and 2-cycle oil. Pre-mix unleaded petrol
and 2-cycle engine oil in a clean container approved
for petrol.
■ ■ ■ ■ ■ This engine is certified to operate on unleaded petrol
intended for motor vehicle use with an octane rating of
87 ([R + M] / 2) or higher.
■ ■ ■ ■ ■ Do NOT use any type of pre-mixed petrol/oil from fuel service
stations. This includes the pre-mixed petrol/oil intended for
use in mopeds, motorcycles, etc.
■ ■ ■ ■ ■ Use a high quality 2-cycle self-mixing oil for air-cooled
engines. Do not use motor vehicle oil or 2-cycle outboard oil.
■ ■ ■ ■ ■ Mix 2% oil into the petrol. This is a 50:1 ratio.
■
■ ■ ■ ■ Mix the fuel thoroughly each time before refuelling.
■
■ ■ ■ ■ Mix in small quantities. Do not mix quantities larger than
usable in a 30-day period. A 2-cycle oil containing a fuel
stabiliser is recommended.
1 Litre + 20 ml =
2 Litres + 40 ml =
3 Litres + 60 ml =
4 Litres + 80 ml =
5 Litres + 100 ml =
CHAIN OIL SYSTEM
See Figure 7.
Use HOMELITE Bar and Chain Oil. It is designed for chains
and chain oilers, and is formulated to perform over a wide
temperature range with no dilution required. Chainsaw should
use approximately one tank of oil per tank of fuel.