Honeywell VCC-600N/P User Manual

Vcc n/p 600n/p

Advertising
background image

Operation Manual

VCC

VCC

-

-

600N/P

600N/P

※ Thank you for choosing Honeywell VCC-600N/P camera.

Please read these instructions carefully before operating this unit,
and retain this manual for future reference.
If you have any problems with this camera, contact your local
supplier to service.

OSD Color Camera

The contents of the package
Check the below contents

- VCC-600N/P Camera 1set
- Auto Iris Lens Plug
- L Type Wrench
- Operation Manual (English)

Printed in Korea

D-100073-001, REV.0

Honeywell Security Group
Honeywell Co., Ltd.
Address: 5F, Sangam IT Tower, B4 - 4block, 1590
Sangam-dong, Mapo-gu, Seoul 121-835, Republic of
Korea
TEL: +82 2 799 6020 / 6395 / 6006
FAX: +82 2 792 9011
E-mail: info.security@honeywell.com

UP BUTTON

+

-

MD

VIDEO

LENS

DC12V

POWER

ENTER

DC

VSD

CONT

ENTER BUTTON

(-) BUTTON

(+) BUTTON

DOWN BUTTON

LENS CONNECTOR

VIDEO OUTPUT

Lens Type Select Switch

POWER ON LED

Power Input Terminal and MD Alarm Output

1. Water and Moisture

To prevent fire or shock hazard, do not expose this camera

to rain or moisture.

2. Servicing

Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.

3. Power Sources

To prevent electric shocks and risk of hazards, do NOT use
more than the specified power source.

4. Environment

Do not install too warm or too cold place. Recommended
operation temperature is between -5℃ and 50℃

5. Sunlight

Do not point the camera at the sun. CCD can be damaged.

6. Heavy Shock and Vibration

Do not drop the camera or subject it to heavy shock of
vibration.

7. Install on an Unstable Place

Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance

.

CAUTION for SAFETY OPERATION

8. When operation is incorrect or a malfunction is observed

While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.

9. Cleaning

Turn the power off and wipe off the dirt with a dry soft
cloth. If it is extremely dirty, use furniture cleaner to wipe it
off. To clean the lens, use a blower or lens cleaning
tissue. (available from any camera dealer)

10. Do not shoot any source of bright light.

If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid
- state pickups, and is not a malfunction.

11. Damage Requiring service

Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:
A. If the power-supply cord or plug is damaged.
B. If the camera has been exposed to rain or water.
C. If liquid has been spilled, or objects have fallen into the camera.
D. If the camera does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the camera to its normal operation.

E. If the camera has been dropped or the cabinet has been damaged.
F . If the camera exhibits a distinct change in performance.
G. Warranty is not covered in case of natural disaster or wrong

Installation.

INSTRALLATION

Mounting a lens
1. Remove the Protective cap in front of the camera.
2. Confirm the mount ring whether it is for C or CS.
3. Attach the lens to the lens mount ring.
4. If the lens has an Auto Iris mechanism, connect the iris cable to the

LENS in rear of the camera.

① In the case of having no iris amplifier : Set the slide switch to

DC (Down side).

② In the case of having iris amplifier : Set the slide switch VSD

(Upper side)
※ When connecting Auto iris lens, be sure to use the connector to

be recommended by manufacturer.( E4-191, ChuoMusen, Japan)

VSD LENS PIN CONFIGURATION

1

2

3

4

1. Power(12V)

2. No Connection

3. Video Signal 4. GND

①③

DC IRIS LENS PIN CONFIGURATION

1

2

3

4

1. Control -

2. Control +

3. Drive +

4. Drive -

①③

Back focus adjustment
1. In case of fixed focus lens
① Loosen the locking ring with L type wrench and set the focus ring

of lens to infinity ( ∞ ).

② Tune the mount ring to get a clear picture( distance from camera

to object is more than 23m) and fasten the locking ring.

2. In case of zoom lens
① Loosen the locking ring with L type wrench and set the lens to the

maximum telephoto position. Then turn the focus ring to focus.
※ In the case of Auto iris lens only, shoot a comparatively dark

object or reduce the ambient light so that the aperture is fully open.

② Set the lens to its maximum wide angle position, and set the focus.
③ Repeat step ① and ②, until the difference between focusing

position ① and ② is smallest.

④ When the best focusing point in found, fasten the locking ring.

Connection of power supply
Must be checked the power source from the external power supply
before power on.

TROUBLESHOOTING

DIMENSIONS

+

-

MD

VIDEO

LENS

DC12V

PO WER

E NTER

D C

VSD

CO NT

+

-

MD

VIDEO

LENS

DC12V

PO WER

E NTER

D C

VSD

CO NT

Unit: mm

Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.

In case of no image
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly?
In case of unclear image
Is the lens in focus?
Is the lens dirty?
Is the monitor adjusted correctly?
※ Dirt of fingerprints on the lens can adversely affect the

images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).

NAMES & FUNCTIONS

OSD MENU

GENERAL SETUP

SYNC

SYNC LEVEL adjustment (0

1…255)

BURST

BURST LEVEL adjustment (0

1…255)

CONTRAST

CONTRAST LEVEL adjustment

(0

1…100)

RETURN

Return to the previous menu.

CAMERA SETUP

AE MODE

LENS MODE, SHUTTER, AGC, BRIGHTNESS, MAX AGC,
MAX FIELDS, etc.

WB MODE

AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,
MANUAL, etc.

BLC MODE

OFF, BLC, WDR, BMB and

their level, area setting.

PZM SET

Privacy Zone Masking function setting.

NIGHTSHOT

Day

 Night, Night  Day mode setting.

CAMERA ID

Camera ID and Position setting.

RETURN

Return to the previous menu.

MEM FUNC. SETUP

DNR MODE

Digital Noise Reduction mode

setting. (OFF

LOWHIGH)

PIP MODE

Picture-in-picture mode setting.

QUAD MODE

Quad display mode setting.

MD MODE

Motion Detection mode setting.

D.ZOOM

Digital Zoom setting. (OFF

1.0x…16.0x)

MIRROR

Mirror mode setting. (OFF

H.MIRRORV.MIRRORFLIP)

RETURN

Return to the previous menu.

SPECIAL SETUP

SHARPNESS

Sharpness compensation setting. (0~15)

GAMMA

Gamma compensation setting. (0.36~1/USER , 8steps)

LANGUAGE

OSD Language setting. (ENG, KOR, JPN, CHI1, CHI2)

RETURN

Return to the previous menu.

DEFAULT SETUP

FACTORY DEFAULT

Set to the Factory Default.

RETURN

Return to the previous menu.

EXIT SETUP

SAVE AND EXIT
EXIT
RETURN

Return to the previous menu.

This LED is ON
in power ON state.

Composite Video
Signal Output

DC Lens: with no iris amp.
VSD Lens: with iris amp.

SPECIFICATIONS

Operational

Image Sensor

Total Pixel

Effective Pixel

Scanning System

Scanning Frequency

Sync System

S/N Ratio

Min. illumination

Horizontal Resolution

Video Output

Lens Iris Control

Electronic Shutter

AGC

Back Light Compensation

White Balance

Electrical

Rated Voltage

Power Consumption

Mechanical & Environmental

Lens Mount

Weight

Dimensions

Front & Rear Color

Body Color

Operating Temp.

Storage Temp.

Operating Humidity

SONY 1/3” Super HAD CCD

410,000 Pixels

470,000 Pixels

380,000 Pixels

440,000 Pixels

525 Lines, 2:1 Interlace

625 Lines, 2:1 Interlace

15.734kHz(H), 59.94Hz(V)

15.625kHz(H), 50Hz(V)

INTERNAL

More than 50dB

0.1lx (F=1.2, 50IRE)
0.001lx (F=1.2, 50IRE, MAX FIELDS x512)

VBS 1.0Vp-p / BNC

MANUAL / DC / VSD

1/60 ~ 1/100,000 sec

1/50 ~ 1/100,000 sec

OFF - 36dB

OFF / BLC / WDR / BMB

AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL

DC12V ± 2V

CS Mount

61.6[W] x 52.4[H] x 77.8[D]mm

Pantone Color 11C (Gray)

Gray

-10°C ~ +50°C

-20°C ~ +70°C

90% RH (non-condensing)

540 TV Lines

NTSC

PAL

Video Standard

1.5W (max)

181g

VCC-600N

VCC-600P

MODEL NAME

Advertising