Harman-Kardon AVR 135 - Manual (Page 32)

32 ADVANCED FEATURES
Advanced Features
Press the ⁄ Button D, until the on-screen ➞
cursor is next to the ADVANCED line. Press
the Set Button F to enter the
ADVANCED
SELECT menu.
At the ADVANCED SELECT menu make
certain that the on-screen ➞ cursor is next to the
SEMI OSD line by pressing the ⁄ / ¤ buttons
D as needed. Next, press the
› button a so
that the word OFF is shown in the video dis-
play.
Note that this setting is temporary and will
remain active only until it is changed or until the
AVR is turned off. Once the unit is turned off, the
semi-OSD displays will remain activated, even if
they were switched off for the previous listening
session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED SELECT Menu as outlined
earlier, and press the ⁄ / ¤ buttons D as need-
ed, until the on-screen ➞ cursor is next to the
SEMI-OSD TIME OUT line. Next, press
the ‹ / › Buttons Ea until the desired time
in seconds is displayed. Note that unlike most of
the other options in this menu, this is a perma-
nent setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
menu, press the
⁄ / ¤ Buttons D until the on-
screen ➞ cursor is next to the desired setting or
the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
Full-OSD Time Out Adjustment
The FULL OSD menu system is used to
simplify the setup and adjustment of the AVR
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of inac-
tivity before they disappear from the screen or
Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the CRTs
in your monitor or projector, which might happen
if they were left on indefinitely. However, some
viewers may prefer a slightly longer or shorter
period before the Time Out display.
To change the Full-OSD Time Out, you will need
to make an adjustment in the
ADVANCED
SELECT menu (Figure 11). To start the adjust-
ment, press the OSD button L to bring the
MASTER MENU to the screen. Press the ⁄
button D, until the on-screen ➞ cursor is next
to the ADVANCED line. Press the Set Button
F to enter the
ADVANCED SELECT
menu (Figure 11).
At the ADVANCED SELECT menu make
certain that the on-screen ➞ cursor is next to the
FULL OSD TIME OUT line by pressing the
⁄ / ¤ Buttons D as needed. Next, press the
‹ / › buttons Ea until the desired time is
displayed in seconds. Note that unlike most of
the other options in this menu, this is a perma-
nent setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
menu, press the
⁄ / ¤ Buttons D until the
on-screen ➞ cursor is next to the desired setting
or the BACK T O MASTER MENU line and
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
If you wish to make other adjustments, press the
⁄ / ¤ Buttons D until the on-screen ➞ cursor
is next to the desired setting or the RETURN
T O MASTER MENU line and press the Set
Button F. If you have no other adjustments to
make, press the OSD Button L to exit the
menu system.