Document Outline

• MX2800 M13 Multiplexer User Manual
  • Trademarks
  • To the Holder of the Manual
  • Revision History
  • Conventions
  • FCC Radio Frequency Interference Statement
  • Canadian Emissions Requirements
  • Canadian Equipment Limitations
  • Training
• Contents
  • Figures
  • Tables
• Section 1, Product Overview
  • 1. Introduction
  • 2. Controller Card 1:1 Redundancy
  • 3. T3 Overview
  • 4. SNMP
    • Network Manager
    • Agent
    • MIB
  • 5. Telnet
  • 6. TL1
  • 7. Available Options
    • Breakout Panel (P/N 1200291L1)
    • E1 Patch Panel (P/N 1200291L5)
    • Battery Backup (P/N 4175043L2)
    • Fan Faceplate (P/N 1200466L1)
• Section 2, Installation and Operation
  • 1. Introduction
  • 2. Receiving Inspection
  • 3. ADTRAN Shipping Contents
  • 4. Power Up
  • 5. Rackmount Installation
    • Connecting the Breakout Panel
    • Connecting the E1 Patch Panel
  • 6. Rear Panel
    • LAN Port
    • Modem Port
    • Noncritical and Critical Alarm Connectors
    • DSX-3 Interfaces
    • DSX-1/E1 Interfaces
    • Power Connection
  • 7. Front Panel
    • Craft Port
      • Establishing Terminal Connection
      • Main Menu
      • Navigating Within the Menus
        • Status
        • Statistics
        • Configuration
        • Loopbacks
        • Telnet Client
        • Logout
        • Privilege Level
    • ACO Buttons
    • LED Descriptions
      • Power Supply A/B Status LEDs
      • Controller Cards Status LEDs
      • T1/E1 Status LEDs
  • 8. Replacing or Installing Cards
• Section 3, Configuration
  • 1. Introduction
  • 2. Network Interface
    • DS3 Configuration
      • Framing
      • Line Length
      • Timing
      • Remote Loopbacks
      • XCV Threshold
    • Protection Configuration
      • Active Controller
      • Network Protection
      • Maximum Switch Threshold
      • Min. Switching Period
    • Miscellaneous
      • Loopback Timeout
      • Shutdown Stand-By
    • DS2 Configuration
  • 3. T1/E1 Interface
    • T1/E1 State
      • Set Multiple
    • T1/E1 Line Coding
    • T1/E1 Line Length
    • T1/E1 Loopback Detection
    • T1/E1 Circuit Protection
    • T1/E1 Line Identification
    • XCV Threshold
  • 4. System Management
    • Management Options
      • Local IP Address
      • Gateway IP Address
      • Subnet Mask
      • Modem Remote IP Address
      • Management Port
      • Forward IP to Remote DS3
      • DS3 Remote IP Address
      • DS3 IP MTU
      • Dialup Options
        • Primary and Secondary Phone Numbers
        • Initializing String
        • Dial String
        • Maximum Redial Attempts
        • Idle Timeout
        • Connection Timeout
        • Pause Between Calls
        • Dialout On Trap
        • Answer on Ring
        • Modem Mode
        • Modem Baud Rate
        • Hangup
        • Last Modem Response
    • SNMP Management Options
      • SNMP State
      • Trap IP Addresses
      • Trap Generation
      • Read Community Name
      • Write Community Name
      • Trap Community Name
      • System Name
    • Network Date/Time Option
      • State
      • Server IP Address
      • Refresh Period
      • DST Automatic Adjustment
      • Local Time Zone
    • System Security
      • User Account Management
        • Guest
        • Interface
        • Test
        • Admin
      • RADIUS Authentication
        • RADIUS State
        • Server IP Address
        • UDP Port
        • Privilege Level
        • Shared Secret Visibility
        • Shared Secret
        • Response Timeout
        • Maximum Retries
      • Terminal Time Out
      • IP Security
      • IP Hosts
    • Date and Time
    • Miscellaneous
      • Alarm Relay Configuration
      • Equipment Identification
        • Unit ID
        • Facility ID
        • Location ID
        • Frame ID
        • Unit Code
        • Equipment Codes
      • Syslog Setup
        • Transmission
        • Host IP Address
        • Severity Level
        • Host Facility
      • Auto Save
      • Craft Baud Rate
  • 5. Utilities
    • Loading Default Settings
      • Load Default Settings Other Than System Management
      • Load System Management Default Settings
      • Load All Default Settings
    • Updating Software
      • Update Via XModem
    • Configuration Transfer
      • Saving to a TFTP Server
      • Retrieving from a TFTP Server
    • Resetting the System
  • 6. Save Configuration and Alarm Log
• Section 4, Status
  • 1. Introduction
  • 2. DS3 State
    • Rx Framing
    • State
    • Alarm
    • Remote
  • 3. Power Supply State
  • 4. System State
    • Alarm
    • Protection
    • Card Comm
  • 5. DS2 State
  • 6. T1/E1 State
  • 7. Acknowledge Alarms (ACO)
• Section 5, Statistics
  • 1. Introduction
  • 2. Viewing Statistical Information
    • DS3 Statistics
      • 24 Hour Alarm History
      • Performance Parameters
        • Interval starting at:
        • Unavailable Seconds (UAS)
        • Severely Errored Framing Seconds (SEFS)
        • Line Coding Violation (LCV)
        • Line Errored Seconds (LES)
        • P-Bit Errored Seconds (PES)
        • P-Bit Severely Errored Seconds (PSES)
        • P-Bit Coding Violations (PCV)
        • C-Bit Code Violations (CCV)
        • C-Bit Errored Seconds (CES)
        • C-Bit Severely Errored Seconds (CSES)
        • F-Bit Errors (FBE)
        • Far End Block Error (FEBE)
        • Clear All Local DS3 Statistics/Refresh All Remote Statistics
    • DS2 Statistics
      • 24-Hour Alarm History
      • Performance Parameters
    • T1/E1 Statistics
  • 3. Protection Switch Statistics
    • Performance Parameters
    • Alarm Log
• Section 6, Loopbacks
  • 1. Introduction
  • 2. T1/E1 Loopbacks
    • Data Mode
    • Tributary
    • Analog Network
    • Digital Line/Net
    • Codec Line/Net
    • Remote Loopback
    • CSU Loopback
    • CSU Loopback w/BERT
    • Line BERT
  • 3. DS3 Loopbacks
    • Line Loopback
    • Digital Loopback
    • Metallic Loopback
    • Remote Loopback
    • Remote All T1/E1
  • 4. DS2 Loopbacks
    • DS2 Network
• Section 7, Circuit and Network Redundancy
  • 1. Introduction
  • 2. Nonredundant Mode
  • 3. Circuit Failure Recovery Mode
  • 4. Circuit and Network Failure Recovery Mode
• Section 8, Power Loss Recovery
  • 1. Introduction
  • 2. Nonredundant Power Mode
  • 3. Power Supply Recovery Mode
  • 4. Power Supply and Source Recovery Mode
  • 5. Battery Backup Mode
• Section 9, Transaction Language 1 (TL1)
  • 1. Introduction
  • 2. Overview
  • 3. TL1 Messages
    • TL1 Responses
      • Acknowledgment Messages
        • In Progress
        • All Right
      • Output Response Messages
      • Autonomous Messages
  • 4. TL1 Commands
    • TL1 Autonomous Messages
  • 5. TL1 Error Codes
    • TL1 Editing
      • TL1 Editing Examples:
      • Data Dictionaries
      • TL1 Loopback Commands
• Appendix A, Acceptance Test Procedure
  • 1. Introduction
  • 2. Verifying the Installed Options
  • 3. Configuring the System
    • Accessing the Craft Port
    • Provisioning the DS3 Port
      • DS3 Configuration
      • Protection Configuration
      • Miscellaneous
      • DS2 Configuration
    • Provisioning the DS1 Ports
    • Alarm Relay Configuration
  • 4. Verifying the Data Integrity
    • DS1 Daisy-Chain to DS3 (Hard) Loopback
    • DS1 to DS3 Head-to-Head Test
    • DS1 to DS3 (Hard) Loopback
  • 5. Verifying Alarm Notification
    • Critical Alarm Relay Test
    • Noncritical Alarm Relay Test
  • 6. Verifying System Redundancy
    • Power Supply Redundancy
      • Single Power Supply Module / Dual Power Feeds
      • Dual Power Supply Modules / Dual Power Feeds
    • Controller Card Redundancy
  • 7. Restoring Default Settings
  • 8. Configuring the System for Traffic Readiness
  • 9. Signing-off the MX2800 ATP Checklist
• Appendix B, Pinouts
• Appendix C, Specifications Summary
  • 1. Introduction
  • 2. Specifications and Features
    • DSX-3 Network Interface
    • DSX-1 Interface(s)
    • Clocking
    • Loopbacks
      • DS3 Network
      • DS2 Interfaces
      • DSX-1 Interfaces
    • Management
      • VT100 Terminal Interface
      • Integrated Modem Interface (4200290L1, 4200290L2, 4200290L3, 4200290L4)
      • SNMP/Telnet
    • Alarms
    • Agency Approvals
    • Environment
    • Power
    • Physical
• Appendix D, Acronyms/Abbreviations
• Appendix E, Glossary
• Appendix F, Warranty
  • 1. Warranty and Customer Service
  • 2. ADTRAN Sales
  • 3. ADTRAN Technical Support
  • 4. ADTRAN Repair/CAPS
  • 5. Repair and Return Address
• Index