Allied Telesis AT-9424Ts/XP (Basic Layer 3) Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for AT-9424Ts/XP (Basic Layer 3) Allied Telesis
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 82 |
| Size: | 5.68 MB |
Show table of contents
Read manual
Document Outline
- Contents
- Preface
- Chapter 1
- Overview
- Descriptions
- 10/100/1000Base-T Twisted Pair Ports
- Fiber Optic Ports
- GBIC Transceiver Slots
- SFP Transceiver Slots
- XFP Transceiver Slots
- Redundant Twisted Pair Ports
- Compact Flash Card Slot
- Port LEDs
- System LEDs
- Stack LEDs
- Expansion Slot
- Terminal Port
- Power Over Ethernet
- AT-RPS3204 Redundant Power Supply
- AC Power Connector
- Overview
- Chapter 2
- Installing the Switch
- Reviewing Safety Precautions
- Selecting a Site
- Twisted Pair and Fiber Optic Cable Specifications
- Unpacking the Switch
- Installing the Power Cord Retaining Clip (AC Switches Only)
- Installing the Switch in a Rack
- Installing Optional Transceivers
- Cabling the Twisted Pair or Fiber Optic Ports
- Applying AC Power
- Starting a Local Management Session
- Warranty Registration
- Installing the Switch
- Chapter 3
- Troubleshooting
- Power LED is Off
- Twisted Pair Port Link LED is Off
- Fiber Optic Port Link LED is Off
- Transceiver is Installed but the Status is “Not Present”
- System Fault LED is Blinking
- System Fault LED is Steadily On
- PoE Device is Not Receiving Power
- Cannot Establish a Local (Out-of-Band) Management Session
- Switch Functions Intermittently
- Troubleshooting
- Appendix A
| Recognized languages: | English |
|---|---|
| Pages: | 108 |
| Size: | 1.17 MB |
Show table of contents
Read manual
Document Outline
- Preface
- Chapter 1
- Overview
- Chapter 2
- Installing the Hardware
- Installation Overview
- Reviewing the Safety Precautions
- Planning the Installation of a Stack
- Maximum Number of Switches in a Stack
- Unpacking a Switch
- Installing the AT-StackXG Stacking Module
- Installing the Power Cord Retaining Clip (AC Switches Only)
- Disconnecting the Network Cables
- Installing the Switches in an Equipment Rack
- Labeling the Switches
- Chapter 3
- Preparing the Switches
- Chapter 4
- Cabling and Powering on the Stack
- Chapter 5
- Cabling the Network Ports
- Chapter 6
- Adding and Removing Switches
- Chapter 7
- Troubleshooting
- No Master Switch
- Power LED is Off
- Twisted Pair Port Link LED is Off
- Fiber Optic Port Link LED is Off
- Transceiver is Installed but the Status is “Not Present”
- System Fault LED is Blinking
- System Fault LED is Steadily On
- Cannot Establish a Local (Out-of-Band) Management Session
- Switch Functions Intermittently
- Appendix A
- Technical Specifications
| Recognized languages: | English |
|---|---|
| Pages: | 106 |
| Size: | 1.49 MB |
Show table of contents
Read manual
Document Outline
- Table of Contents
- Preface
- Chapter 1
- Overview
- Chapter 2
- Installing the Hardware
- Installation Overview
- Reviewing the Safety Precautions
- Planning the Installation of a Stack
- Maximum Number of Switches in a Stack
- Unpacking a Switch
- Installing the AT-StackXG Stacking Module
- Installing the Power Cord Retaining Clip (AC Switches Only)
- Disconnecting the Network Cables
- Installing the Switches in an Equipment Rack
- Labeling the Switches
- Chapter 3
- Preparing the Switches
- Chapter 4
- Cabling and Powering on the Stack
- Chapter 5
- Cabling the Network Ports
- Chapter 6
- Adding and Removing Switches
- Chapter 7
- Troubleshooting
- No Master Switch
- Power LED is Off
- Twisted Pair Port Link LED is Off
- Fiber Optic Port Link LED is Off
- Transceiver is Installed but the Status is “Not Present”
- System Fault LED is Blinking
- System Fault LED is Steadily On
- Cannot Establish a Local (Out-of-Band) Management Session
- Switch Functions Intermittently
- Appendix A
- Technical Specifications
| Recognized languages: | English |
|---|---|
| Pages: | 84 |
| Size: | 2.09 MB |
Show table of contents
Read manual
Document Outline
- Electrical Safety and Emissions Standards
- Translated Safety Statements
- Contents
- Preface
- Chapter 1
- Overview
- Descriptions
- 10/100/1000Base-T Twisted Pair Ports
- Fiber Optic Ports
- GBIC Transceiver Slots
- SFP Transceiver Slots
- XFP Transceiver Slots
- Redundant Twisted Pair Ports
- Compact Flash Card Slot
- Port LEDs
- System LEDs
- Stack LEDs
- Expansion Slot
- Terminal Port
- Power Over Ethernet
- AT-RPS3204 Redundant Power Supply
- AC Power Connector
- Chapter 2
- Installing the Switch
- Reviewing Safety Precautions
- Selecting a Site
- Twisted Pair and Fiber Optic Cable Specifications
- Unpacking the Switch
- Installing the Power Cord Retaining Clip (AC Switches Only)
- Installing the Switch in a Rack
- Installing Optional Transceivers
- Cabling the Twisted Pair or Fiber Optic Ports
- Applying AC Power
- Starting a Local Management Session
- Warranty Registration
- Chapter 3
- Troubleshooting
- Appendix A
- Technical Specifications