Document Outline

• 010623b1e_Specs.pdf
  • Power Module Output
  • Power Module Input
  • Environmental
  • Miscellaneous
  • Safety
  • Other Referenced Standards
• 0100002-S0b_12kW_specs.pdf
  • Power Module Output
  • Power Module Input
  • Environmental
  • Miscellaneous
  • Safety
  • Other Referenced Standards
• 010600b1c_3.6kW_specs.pdf
  • Power Module Output
  • Power Module Input
  • Environmental
  • Miscellaneous
  • Safety
  • Other Referenced Standards
• 9400000j0c_body.pdf
  • Figure 1 — (a) Cordex 48-3.6kW (b)Cordex 48-4kW (c) Cordex 48-12kW switched mode rectifier
  • Figure 2 — Rectifier front panel LEDs
  • Figure 3 — Cordex CXCM4 model system controller front panel
  • Figure 4 — Rectifier (or Converter) report screen
  • Figure 5 — CAN termination selection and serial ports
  • Figure 6 — Relay connections in the de-energized state
  • Figure 7 — Digital input connection method
  • Figure 8 — LVD override control and distribution alarm card
  • Figure 9 — Fan assembly - screw removal
  • Figure 10 — Fan assembly
  • 1. Safety
    • 1.1 Safety Symbols
    • 1.2 General Safety
    • 1.3 Mechanical Safety
    • 1.4 Electrical Safety
    • 1.5 Battery Safety
  • 2. Introduction
    • 2.1 Scope of the Manual
    • 2.2 Product Overview
    • 2.3 Part Numbers and List Options
  • 3. Rectifier Features
    • 3.1 Front Panel
    • 3.2 Rectifier Rear Panel
    • 3.3 True Module Fail Alarm
    • 3.4 Heat Dissipation
    • 3.5 Over Temperature Protection
    • 3.6 Wide AC Range
    • 3.7 AC Inrush/Transient Suppression
    • 3.8 Soft Start
    • 3.9 Start Delay
    • 3.10 Current Limit/Short Circuit Protection
    • 3.11 Power Limiting
    • 3.12 High Voltage Shutdown (HVSD)
    • 3.13 Battery Eliminator Operation
  • 4. Cordex System Controller (CXC)
    • 4.1 CXCM4 Features
    • 4.2 Controller Front Panel
    • 4.3 Rectifier Report from Controller Display
    • 4.4 Analog Input Channels
    • 4.5 Digital Input Channels
    • 4.6 Alarm and Control Output Relays
    • 4.7 System Fail Alarm/Relay
  • 5. Inspection
    • 5.1 Packing Materials
    • 5.2 Check for Damage
    • 5.3 General Receipt of Shipment
  • 6. Installation
    • 6.1 Safety Precautions
    • 6.2 Tools Required
    • 6.3 Power System Assembly and Mounting
  • 7. Wiring
    • 7.1 Grounding
    • 7.2 AC Feeder Protection/Sizing
    • 7.4 DC Output Connections
    • 7.3 AC Input Connections
    • 7.5 CAN Serial Ports (Rectifier Shelf)
    • 7.6 Inserting the CXCM4 Module
    • 7.7 Signal Wiring Connections for CXCM4
    • 7.8 Network Connection and Remote Communications via CXC
  • 8. System Startup
    • 8.1 Check System Connections
    • 8.2 Verify AC and Power the Rectifier Shelf
    • 8.3 Triple Check Battery Polarity and Connections
    • 8.4 CXC Reset
  • 9. Rectifier States, Modes and Factory Defaults
    • 9.1 Main Rectifier States
    • 9.2 Main Rectifier Modes
    • 9.3 Factory Ranges and Defaults
  • 10. Maintenance
    • 10.2 Replacing a Rectifier Module
    • 10.3 Replacing the CXCM4 Module
    • 10.4 Fan and Fan Filter Replacement
    • 10.5 MOV Replacement
  • 11. Acronyms and Definitions
  • 12. Warranty and Service Information
    • 12.1 Technical Support
    • 12.2 Warranty
    • 12.3 Battery Warranty
    • 12.4 Return of Material