Document Outline

• ATCA-7368
• Contents
• Safety Notes
  • EMC
  • Installation
  • Operation
  • Switch Settings
  • Battery
  • Environment
• Sicherheitshinweise
  • EMV
  • Installation
  • Betrieb
  • Schaltereinstellungen
  • Batterie
  • Umweltschutz
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Introduction
  • 1.1 Features
  • 1.2 Standard Compliances
  • 1.3 Mechanical Data
  • 1.4 Mechanical Layout
  • 1.5 Ordering Information
  • 1.6 Product Identification
• Hardware Preparation and Installation
  • 2.1 Overview
  • 2.2 Unpacking and Inspecting the Blade
  • 2.3 Environmental and Power Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Power Requirements
  • 2.4 Blade layout
  • 2.5 Installing the Blade Accessories
    • 2.5.1 DIMM Memory Modules
    • 2.5.2 PMEM and SATA Module
    • 2.5.3 USB 2.0 Flash Module
  • 2.6 Installing and Removing the Blade
    • 2.6.1 Installing the Blade
    • 2.6.2 Removing the Blade
• Controls, Indicators, and Connectors
  • 3.1 Overview
  • 3.2 Faceplate
    • 3.2.1 LEDs and Interfaces
    • 3.2.2 Connectors
      • 3.2.2.1 Faceplate Connectors
  • 3.3 Onboard Connectors
    • 3.3.1 USB2.0 FLASH Connector
    • 3.3.2 Backplane Connectors
    • 3.3.3 Zone 3
• BIOS
  • 4.1 Overview
  • 4.2 Accessing the Blade using the Serial Console Redirection
    • 4.2.1 Requirements
    • 4.2.2 Default Access Parameters
    • 4.2.3 Connecting to the Blade
  • 4.3 Changing Configuration Settings
  • 4.4 Boot Options
    • 4.4.1 Supported Boot Devices
    • 4.4.2 Selecting The Boot Device
    • 4.4.3 By Boot Selection Menu
    • 4.4.4 Network boot
  • 4.5 Redirection of I/O
    • 4.5.1 Redirection of the I/O to COM ports (Console Redirection)
  • 4.6 LED behavior during POST
  • 4.7 LED Usage
  • 4.8 RTM SAS Controller
  • 4.9 Board Information Display
  • 4.10 USB Ports
  • 4.11 Supported Operating Systems
  • 4.12 Persistent Memory Module
  • 4.13 Upgrading the BIOS
  • 4.14 BIOS Error Messages
  • 4.15 BIOS Status Codes
    • 4.15.1 Status Code Ranges
    • 4.15.2 Standard Status Codes
• Functional Description
  • 5.1 Overview
  • 5.2 Block Diagram
  • 5.3 Processor
  • 5.4 Memory
    • 5.4.1 DDR3 Main Memory
  • 5.5 Chipset
  • 5.6 I/O Controller
  • 5.7 Persistent Memory Module (PMEM)
  • 5.8 Ethernet Ports
  • 5.9 Storage
  • 5.10 IPMC
  • 5.11 Serial Redirection
  • 5.12 Serial Over LAN
  • 5.13 IPMI Over LAN
  • 5.14 USB 2.0 Interface
  • 5.15 SMBus Connections
  • 5.16 Real Time Clock
  • 5.17 Single Width Mid-size AMC
• Serial Over LAN
  • 6.1 Overview
  • 6.2 Installing the ipmitool
  • 6.3 Configuring SOL Parameters
    • 6.3.1 Using Standard IPMI Commands
    • 6.3.2 Using ipmitool
  • 6.4 Establishing a SOL Session
• Supported IPMI Commands
  • 7.1 Overview
  • 7.2 Standard IPMI Commands
    • 7.2.1 Global IPMI Commands
    • 7.2.2 System Interface Commands
    • 7.2.3 Watchdog Commands
    • 7.2.4 SEL Device Commands
    • 7.2.5 FRU Inventory Commands
    • 7.2.6 Sensor Device Commands
    • 7.2.7 Chassis Device Commands
      • 7.2.7.1 System Boot Options Commands
    • 7.2.8 LAN Device Commands
  • 7.3 PICMG 3.0 Commands
  • 7.4 Artesyn Specific Commands
    • 7.4.1 Set/Get Feature Configuration
      • 7.4.1.1 Set Feature Configuration (0x1E)
      • 7.4.1.2 Get Feature Configuration (0x1F)
    • 7.4.2 Serial Output Commands
      • 7.4.2.1 Set Serial Output Command
      • 7.4.2.2 Get Serial Output Command
  • 7.5 Pigeon Point Specific Commands
    • 7.5.1 Get Status Command
    • 7.5.2 Get Serial Interface Properties Command
    • 7.5.3 Set Serial Interface Properties Command
    • 7.5.4 Get Debug Level Command
    • 7.5.5 Set Debug Level Command
    • 7.5.6 Get Hardware Address Command
    • 7.5.7 Set Hardware Address Command
    • 7.5.8 Get Handle Switch Command
    • 7.5.9 Set Handle Switch Command
    • 7.5.10 Get Payload Communication Time-Out Command
    • 7.5.11 Set Payload Communication Time-Out Command
    • 7.5.12 Enable Payload Control Command
    • 7.5.13 Disable Payload Control Command
    • 7.5.14 Reset IPMC Command
    • 7.5.15 Hang IPMC Command
    • 7.5.16 Graceful Reset Command
    • 7.5.17 Get Payload Shutdown Time-Out Command
    • 7.5.18 Set Payload Shutdown Time-Out Command
    • 7.5.19 Get Module State Command
    • 7.5.20 Enable Module Site Command
    • 7.5.21 Disable Module Site Command
    • 7.5.22 Reset Carrier SDR Repository Command
• FRU Information and SDR Summary
  • 8.1 Overview
  • 8.2 FRU Information
  • 8.3 E-keying
  • 8.4 Power Configuration
  • 8.5 Sensor Data Records
• A Replacing the Battery
  • A.1 Replacing the Battery
• B Related Documentation
  • B.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • B.2 Related Specifications