Document Outline

• ATCA-F125 (6873M Artwork)
• Contents
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Introduction
  • 1.1 Features
  • 1.2 Standard Compliances
  • 1.3 Mechanical Data
  • 1.4 Ordering Information
    • 1.4.1 Blade Accessories
  • 1.5 Product Identification
• Hardware Preparation and Installation
  • 2.1 Overview
  • 2.2 Unpacking and Inspecting the Blade
  • 2.3 Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Thermal Requirements
    • 2.3.3 Power Requirements
  • 2.4 Rear Transition Modules
  • 2.5 Blade Configuration
    • 2.5.1 SATA Drive Installation
  • 2.6 Blade Installation and Removal
    • 2.6.1 Installing the Blade
    • 2.6.2 Removing the Blade
  • 2.7 AMC Module Installation and Removal
  • 2.8 Installing and Removing SFP Modules
    • 2.8.1 Installing an SFP Module
    • 2.8.2 Removing an SFP Module
• Controls, LEDs, and Connectors
  • 3.1 Overview
  • 3.2 Blade Layout
  • 3.3 Faceplate LEDs
  • 3.4 Reset Switch
  • 3.5 Faceplate Connectors
  • 3.6 Backplane Connectors
    • 3.6.1 Zone 1
    • 3.6.2 Zone 2
    • 3.6.3 Zone 3
  • 3.7 Module Connectors
    • 3.7.1 AMC Connector
    • 3.7.2 SAS/SATA Connector
    • 3.7.3 Embedded USB Connector
    • 3.7.4 Processor COP Header
    • 3.7.5 H8S Console and Programming Header
  • 3.8 Switches
• Functional Description
  • 4.1 Block Diagram
  • 4.2 Processor
  • 4.3 Memory
    • 4.3.1 Memory Interface
    • 4.3.2 Memory Sockets
    • 4.3.3 Memory Modules
    • 4.3.4 Persistent Memory
  • 4.4 IPMI
    • 4.4.1 Temperature Sensors
  • 4.5 FPGA
    • 4.5.1 Serial Configuration PROM
  • 4.6 Boot and User Flashes
    • 4.6.1 Boot Flash Backup Recovery
  • 4.7 Base Channel Interface
    • 4.7.1 Base Channel PHYs
    • 4.7.2 ShMC Cross-Connect
  • 4.8 Fabric Channel Interface
  • 4.9 SFP+ Modules
  • 4.10 AMC Bay
    • 4.10.1 BCM5709S Dual Gigabit Ethernet MAC/PHY
    • 4.10.2 Channel Cross-Connect for BCM5709S
    • 4.10.3 Storage Hard Disk Drive
  • 4.11 Telecom Clocking
    • 4.11.1 Telecom Clocking Subsystem
    • 4.11.2 BITS/SSU Support
  • 4.12 Reset Structure
    • 4.12.1 Service Processor Core Reset Domain
      • 4.12.1.1 Service Processor
      • 4.12.1.2 Memory
      • 4.12.1.3 Onboard Flash
      • 4.12.1.4 Persistent Memory
    • 4.12.2 Ethernet Switch Resets
      • 4.12.2.1 Broadcom BCM56334
      • 4.12.2.2 Broadcom BCM56820
    • 4.12.3 Physical Interconnect Devices
    • 4.12.4 AMC Bay
    • 4.12.5 Rear Transition Module
  • 4.13 Interrupt Structure
• U-Boot
  • 5.1 Overview
  • 5.2 Accessing U-Boot
  • 5.3 Configuring Boot Options
    • 5.3.1 Configuring U-Boot for Network Boot
    • 5.3.2 Configuring U-Boot to Boot from RAM Disk
    • 5.3.3 Configuring U-Boot to Boot from Flash
  • 5.4 Selecting the Boot Flashes
  • 5.5 Using the Persistent Memory Feature
  • 5.6 Memory Map
  • 5.7 Linux Devices
  • 5.8 Power-On Self Test
    • 5.8.1 POST Routines
    • 5.8.2 Controlling the Execution of the POST
  • 5.9 ATCA-F125 Specific U-Boot Commands
  • 5.10 ATCA-F125-Specific U-Boot Environment Variables
  • 5.11 Updating U-Boot
• A Battery Exchange
  • A.1 Replacing the Battery
• B Related Documentation
  • B.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • B.2 Related Specifications
• Safety Notes
• Sicherheitshinweise