Document Outline

• Contents
• About This Document
  • In this chapter
  • How this document is organized
  • Brocade resources
  • Getting technical help
  • Document feedback
• Documentation Updates for the Multi-Service IronWare Configuration Guides
  • In this chapter
  • Configuring a “null” route
  • ACL deny logging
    • Unsupported features for Brocade NetIron CES and Brocade NetIron CER devices
  • Deployment Scenarios and CLI Configuration
  • Telemetry Solutions
    • Scaling limitations
    • Base-line configuration of telemetry solutions
    • Global level configuration
      • Configuring System max and cam-partition
      • Disabling LFS at global level
      • Configuring Ingress tap port
      • Configuring Egress port
      • Configuring ACL
      • Configuring Route-map
  • PIM over MCT
    • MCT feature interaction
  • Multicast snooping over MCT
  • Running configuration sequence number display
    • Example of show run
    • Example of show access-list l2 command
  • DVMRP legacy protocol support
  • LAG formation rules
  • IPTV support on Brocade NetIron CES and Brocade CER devices
  • Configuring a PBR policy
  • HQoS Feature support
  • HQoS for VPLS traffic overview
    • Feature highlights
    • Configuring HQoS for VPLS traffic
    • Limitations
    • Checking for HQoS for VPLS configurations on ports
  • HQoS for LAG traffic overview
    • Feature highlights
    • Configuring steps
    • Limitations
  • WRED support for HQoS
    • Feature highlights
    • Configuring steps
    • Commands
  • Configuring VPLS endpoint over FDP/CDP interface
  • Configuring VLL endpoint over FDP/CDP enabled interface
  • Transparent forwarding of L2 and L3 protocols on a VLL for CES and CER
  • Modify OSPF standard compliance setting
  • VRRP and VRRP-E
  • Configuring an IPv6 Access Control List
  • Start a log file before an upgrade
  • IPv6 packets on Openflow L23 port
    • Before 5.6.00c
    • From 5.6.00c
      • System-max configuration for Openflow
      • Hardware entries usage
  • TM RAS Enhancements
    • TM DRAM CRC error interrupt
      • Examples
    • Descriptive TM error interrupt logging
    • Separate Threshold for CRC logging
      • Examples
      • CLI for SFM and Internal FE
      • Example
  • Simplified Package Upgrade
    • Brocade NetIron XMR and Brocade MLX Series single-command (full-system) upgrade
    • Brocade NetIron CER and Brocade NetIron CES single-command (full-system) upgrade
  • LP auto-upgrade
  • SCP “success message”
  • L2 protocol packet handling
  • OpenFlow configuration considerations
  • Configuring egress buffer threshold
  • TM XPP link status check
    • Examples
  • Flow control handling modification
    • CLI commands
      • Global command
      • Interface command
  • Policy-based routing support for preserve VLAN
  • Deletion of ACLs bound to an interface
  • Optional cluster operation features
  • Enabling a transparent firewall
  • Default VRRP/VRRP-E dead interval calculation
  • IPv6 anycast filtering
  • PBIFS extended counters
  • Limiting log generation for MEP and Remote MEP
  • IPv4 ACL-based rate limiting updates
    • Configuration considerations
    • Configuring a port-and-ACL-based traffic policing policy
    • How the Brocade device processes ACLs
      • General configuration guidelines
  • FE access recovery disable
    • Usage Guidelines
    • Output
  • Setting the delay before bringing up the CCEP port
  • Setting the OpenFlow system maximum
  • IPv6 Multicast Listener Discovery snooping
    • Configuring IPv6 multicast routing or snooping
    • Enabling IPv6 multicast traffic reduction
  • Configuring and enabling sFlow
  • Multicast queue size, flow control, rate shaping and egress buffer threshold
  • Enabling PVST+ support
• Documentation updates for Multi-Service IronWare Diagnostic Guide
• Documentation updates for Unified IP MIB Reference
  • In this chapter
  • Route map configuration table
  • MAC filters
  • RFC 4444: Management Information Base for Intermediate System to Intermediate System (IS-IS)
    • Scalar isisSys objects
      • isisSysMaxPathSplits
  • Rate limit counter index table
    • agRateLimitCounterIndexTable
      • agRateLimitCounterIndexRowIndex
      • agRateLimitCounterIndexDirection
      • agRateLimitCounterIndexVLANID
      • agRateLimitCounterIndexVLANGroupID
      • brcdIp.1.1.3.16.1.3.1.5
      • Syntax: Integer32
      • agRateLimitCounterIndexMACAddress
      • brcdIp.1.1.3.16.1.3.1.6
      • Syntax: MAC address
  • Upgrade MIB Objects
    • brcdSwPackageUpgradeAllI mages
    • brcdSwIntfModAutoUpgrade AllImages
• Documentation Updates for the MLXe / MLX Series and NetIron XMR Series Hardware Installation Guide
  • In this chapter
  • Switch fabric modules
    • Brocade MLXe Series
    • Brocade MLX Series and Brocade NetIron XMR
  • 10Gx24-port interface module
  • MLX 48x1G-T interface module
  • PBIF Recovery
    • Syntax
    • Command Default
    • Examples
  • Router modules