Document Outline

• Title Page
• Notice
• Contents
• Introduction
  • Related Documentation
  • How to Use This Guide
  • Document Conventions
  • Getting Help
• About the CSX200
  • CSX200 Hardware
    • WAN Connection
    • Ethernet LAN Connection
  • Remote Management Capabilities
  • Optional Features
  • CSX200 Firmware Support
    • IEEE 802.3 Ethernet
    • WAN Protocols
    • Firmware Data Compression
    • HDLC
    • DHCP and NAT
    • Frame Relay Protocol
    • Point-to-Point Protocol (PPP)
    • PAP and CHAP Security
    • LQM
    • Multilink Protocol
    • ISDN
    • HDSL
    • Bridging and Routing
    • Bridging and Routing Protocol Filtering
    • System Passwords
    • Simple Network Management Protocol (SNMP)
      • SNMP MIB Support
      • SNMP Trap Support
    • Software and Firmware Upgrades
• 10BASE-T LAN Requirements
  • Network Requirements
    • 10BASE-T Twisted Pair Network
  • Port Descriptions
  • 10BASE-T LAN Configuration
    • Connecting UTP Cables to Ports 1 Through 12
• Installation
  • Unpacking the CSX200
  • Installation Guidelines
    • Removing the CSX200 Cover
    • Installing a WPIM
  • COMP/ENCR Module Installation
  • Installing the CSX200
    • Tabletop and Shelf Installations
  • Rackmount Installation
    • Tools Required
    • Materials Required
    • Attaching the Strain-Relief Bracket
    • Attaching the Rackmount Brackets
    • Installing the CSX200 in a 19-Inch Rack
  • Powering the CSX200
• Troubleshooting
  • Troubleshooting CSX200 Hardware
    • Power (PWR) LED is OFF
    • Processor (CPU) LED is OFF
    • Processor (CPU) LED is RED
  • Troubleshooting the LAN
    • Collision (CLN) LED is RED
    • Link (LNK) LED is OFF
  • Troubleshooting the WAN
    • Link (LNK) LED is OFF
    • Link (LNK) LED is RED
    • Link (LNK) LED is AMBER
    • Status 1 (STS1) LED is OFF
      • WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in CSX200
      • WPIM-SYNC Installed in CSX200
      • WPIM-HDSL Installed in CSX200
    • Status 1 (STS1) LED is RED
      • WPIM-T1, WPIM-E1, or WPIM-DI Installed in CSX200 is in RED Alarm Mode
      • WPIM-HDSL Installed in CSX200
    • Status 1 (STS1) LED is AMBER
      • WPIM-DDS Installed in CSX200
    • Status 1 (STS1) LED is GREEN
      • WPIM-SYNC Installed in CSX200
      • WPIM-HDSL is installed in CSX200
    • Status 2 (STS2) LED is OFF
      • WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in CSX200
      • WPIM-SYNC Installed in CSX200
      • WPIM-HDSL Installed in CSX200
    • Status 2 (STS 2) LED is RED WPIM-HDSL Installed in CSX200
    • Status 2 (STS2) LED is AMBER
      • WPIM-T1, WPIM-E1, or WPIM-DI Installed in CSX200
    • Status 2 (STS2) LED is GREEN
      • WPIM-SYNC Installed in CSX200
      • WPIM-HDSL Installed in CSX200
    • Test (TST) LED is AMBER (blinking)
  • Investigating Software Configuration Problems
    • Connection to Device Fails During Software Configuration
    • User Cannot Communicate with Remote Network Station
      • If Bridging,
      • If TCP/IP Routing,
• WPIM Cable Specifications
  • WPIM-T1
  • WPIM-SY
    • EIA-449
    • V.35
    • EIA-232
    • X.21
    • EIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT A
  • WPIM-DDS
  • WPIM-E1
  • WPIM-DI
  • WPIM-HDSL
• Specifications and Standards Compliance
  • CSX200 Regulatory Compliance
  • Individual WPIM Regulatory Compliance
    • WPIM-T1
    • WPIM-SY
    • WPIM-DDS
    • WPIM-E1
    • WPIM-DI
    • WPIM-HDSL
• FCC Part 68 - User’s Information for CSX200
• Glossary
• Index
  • Numerics
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • P
  • R
  • S
  • T
  • W