Document Outline

• Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide
• Contents
• Preface
• Overview of the Cisco 3825 Mobile Wireless Edge Router
  • Introduction
    • RAN-Optimization Implementation
    • Cisco Abis and Iub Optimization over IP Implementation
      • Cisco GSM Abis Optimization over IP
      • Cisco Pseudowire Emulation Edge-to-Edge (PWE3)
      • Cisco Iub Optimization over IP
    • Intelligent Cell Site IP Services
      • Cell Site Points-of-Presence (POPs)
  • Cisco IOS Software Features
    • Software features for the RAN-O Implementation
      • Software Features
      • Redundancy Support
        • HSRP
      • Configuration Statements for CISCO-IP-RAN-BACKHAUL-MIB
  • MIB Support
  • Limitations and Restrictions
    • RAN-O Implementation Limitations and Restrictions
      • Hardware not Supported on the Cisco 3825 Router
    • UMTS Iub and GSM Abis Implementation Limitations and Restrictions
      • Hardware not Supported for UMTS Iub
      • Hardware not Supported for GSM Abis
  • New Features in Cisco IOS Release 12.4(16)MR2
    • Keyword ignore-vpi-vci Added to xconnect Command
  • New Features in Cisco IOS Release 12.4(16)MR1
    • Emulation of TDM Circuit via MPLS/IP (PWE3/TDM)
      • Structure-agnostic TDM over Packet (SAToP)
      • Structure-aware TDM CESoPSN
    • Transportation of ATM Service via MPLS/IP (PWE3/ATM)
      • Transparent Cell Transport Service/ATM Port Mode
      • ATM N-to-One VCC Cell Mode
      • ATM AAL5 CPCS-SDU Mode
      • ATM One-to-One VCC Cell Mode
        • Cell Packing
        • PVC Mapping
    • Transportation of ATM Service via L2TPv3
      • ATM Port Cell Relay Service
      • ATM VCC Cell Relay Service
      • ATM AAL5-SDU Mode
        • Cell Packing
        • PVC Mapping
    • Asymmetric PWE3
    • Ethernet over MPLS
      • VLAN Mode
      • Port Mode
    • PWE3 over MLPPP
    • PWE3 Redundancy
      • TDM PWE3 Redundancy
      • ATM PWE3 Redundancy
      • Ethernet PWE3 Redundancy
    • Maximum Number of Supported ATM Ports
    • ATM Cell Switching
  • New Features in Cisco IOS Release 12.4(16)MR
    • GSMmux-Global System for Mobile Communication (GSM) Abis Optimization over IP
    • UMTSmux-Universal Mobile Telecommunication System (UMTS) Iub Optimization over IP
    • UMTS Congestion Management Control
    • Inverse Multiplexing over ATM (IMA)
    • Permanent Virtual Circuit (PVC) Routing
      • Behavior Changes
    • UMTS QoS
• Cisco IOS Software Basics
  • Getting Help
  • Understanding Command Modes
  • Undoing a Command or Feature
  • Saving Configuration Changes
  • Where to Go Next
• First-Time Configuration
  • Understanding Boot Images
  • Understanding the Cisco 3825 Router Interface Numbering
    • Slot and Port Numbering
  • Setup Command Facility
    • Before Starting Your Router
    • Using the Setup Command Facility
  • Configuring Global Parameters
  • Completing the Configuration
• Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line Interface
  • Before You Begin
  • Verifying the Version of Cisco IOS Software
  • Clocking Requirements for Cisco 3825 Router
    • Clock-Related Commands
      • Network-Clock-Participate Command
      • Network-Clock-Select Command
      • Clock Source Command
      • Example Configurations
  • Show Controller Command
  • Configuration Sequence
    • Summary of Steps
    • Configuring the Hostname and Password
    • Verifying the Hostname and Password
    • Configuring Gigabit Ethernet Interfaces
      • Configuring the GE Interface IP Address
      • Setting the Speed and Duplex Mode
      • Enabling the GE Interface
    • Configuring the Backhaul Links
      • Configuring the Card Type for the Cisco 2-port T1/E1-RAN
      • Configuring E1 Controllers
      • Configuring T1 Controllers
      • Configuring Network Clocking Support
      • Configuring Multilink Backhaul Interface
        • Creating a Multilink Bundle
      • Handling PFC and ACFC
        • Configuring PFC
        • Configuring ACFC
        • Enable Multilink and Identify the Multilink Interface
        • Enable Real-Time Transport Protocol (RTP) Header-Compression
      • Configuring the PPP Backhaul Interfaces
    • Extended Availability Drop and Insert (EADI)
    • Configuring GSM-Abis Links
    • Configuring UMTS Links
    • Configuring Redundancy
      • Redundant Cisco 3825 Routers
      • Standalone Cisco 3825 Router
    • Configuring for SNMP Support
    • Configuring Inverse Multiplexing over ATM (IMA)
    • Configuring PVC Routing (HSDPA Offload)
    • Configuring UMTS QoS
      • Creating a Class Map
      • Creating a Policy Map
      • Specify the Location of the Interface
      • Assigning a QoS Boilerplate to an Interface
    • Configuring UMTS Congestion Management Control
    • Configuring Satellite Support
    • Configuring Graceful Degradation
  • Saving Configuration Changes
    • Example Configurations
      • BTS/Node-B Configuration
      • BSC/RNC Configuration
  • Monitoring and Managing the Cisco 3825 Router
    • Enabling the Cisco 3825 Router for Remote Network Management
    • Show Commands for Monitoring the Cisco 3825 Router
  • Where to Go Next
• Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference
• Configuration Examples
  • Overview
    • Asymmetric PWE3 Configuration
    • Ethernet over MPLS-VLAN and Port Mode Configuration
    • PWE3 over MLPPP Configuration
    • PWE3 Redundancy Configuration
    • TDM over MPLS Configuration
    • ATM over MPLS Configurations
    • ATM over L2TPv3 Configuration
    • GSM Only Configuration
    • UMTS Only Configuration without IMA
    • Combined GSM and UMTS Configuration
    • GSM and UMTS with IMA Configuration
    • GSM and UMTS with IMA and PVC Routing (HSDPA Offload) Configuration
    • GSM Only Configuration via Satellite
    • GSM Congestion Management
    • UMTS Congestion Management
• Index