Document Outline

• About This Manual
• 1.0 Introduction
• 2.0 Installation and Wiring
  • 2.1 Unpacking and Inspection
  • 2.2 Repacking
  • 2.3 Rear Panel Configuration
  • 2.4 Hardware Configuration and Wiring
  • 2.5 Display/Keyboard Functions
  • 2.6 Freeze Mode
  • 2.6.1 Freeze Mode Specifications
    • 2.7 Min and Max Mode
  • 2.7.1 Resetting Min and Max Values
    • 2.8 Remote Display Mode
• 3.0 Operation
  • 3.1 Initial Setup Procedure
  • 3.2 Pressure Measurement Sequence (Gage)
  • 3.3 Pressure Measurement Sequence (Absolute)
• 4.0 Re-Calibration Only
  • 4.1 Pneumatic Calibration Set-Up
  • 4.2 Instrument Calibration Set-Up
  • 4.3 Re-Calibration Procedure (Zero, Linearity and Hysteresis)
• 5.0 Configuration and Calibration
  • 5.1 Pneumatic Calibration Set-Up
  • 5.2 Instrument Calibration Set-Up
  • 5.3 Mode Selection Switch (S1)
  • 5.4 Main Set-Up Mode Menu Selections
  • 5.5 Auto Set-Up Configuration Mode Selection
  • 5.5.1 Auto Set-Up Menu (General)
  • 5.5.2 Auto Set-Up Menu (Gage)
  • 5.5.3 Auto Set-Up Menu (Absolute)
    • 5.6 Calibration Set-Up Configuration Mode Selection
  • 5.6.1 Calibration Mode Menu
    • 5.7 Modifying Data
    • 5.8 Span Calibration Points
    • 5.9 Resetting Span Calibration Points
    • 5.10 Overwriting Span Calibration Points and Hysteresis
    • 5.11 Configuration Set-Up Mode Selection
    • 5.12 Conversion Set-Up Mode Selection
    • 5.13 I/O Set-Up Mode Selection
  • 5.13.1 Port 1 Set-Up Menu
  • 5.13.2 Port 1 Printer Menu
    • Port 1 Printer Modify Menu
  • 5.13.3 Port 1 Duplex Menu
  • 5.13.4 Port 1 RS485 Menu
  • 5.13.5 Port 1 Simplex Menu
    • Port One Simplex Modify Menu
  • 5.13.6 Port 2 Set-Up
  • 5.13.7 Time and Date Set-Up Menu
  • 5.13.8 Input Set-Up
  • 5.13.9 Print and Zero Wiring Configration Example
• 6.0 Serial Input/Output
  • Port 1 (set up selections)
  • Port 2 (set up selections) - No DUPLEX communication
    • 6.1 ASCII - Data Formats
    • 6.2 Printer (Port One or Port Two)
    • 6.3 Duplex (Port One Only)
  • 6.3.1 Full Duplex Protocol
  • 6.3.2 Command Code <cmd> Description
  • 6.3.3 Basic RS485 Commands
    • 6.4 Continuous Simplex Output (Compressed Format)
    • 6.5 Serial Output Wiring and Hardware Configuration
• 7.0 Maintenance and Service
  • 7.1 Troubleshooting
  • 7.2 Maintenance and Service Procedures
  • 7.2.1 Panel/Chassis Removal and Installation
  • 7.2.2 ORION-2C (PN 55283) or ORION-3A (PN 55287) Manifold Removal
  • 7.2.3 ORION Manifold - Valve Seat Removal
  • 7.2.4 ORION Manifold - Vernier Control Disassembly
  • 7.2.5 ORION Manifold - Vernier Control Reassembly
  • 7.2.6 ORION-2C Manifold - Valve Seat Installation
  • 7.2.7 ORION Manifold - Panel Installation
  • 7.2.8 ORION-2C Manifold - Valve Adjustment Procedure
  • 7.2.9 ORION-3A Manifold - Valve Adjustment Procedure
  • 7.2.10 Pressure Limit Control (Standard Pneumatic), Regulator Removal
  • 7.2.11 Pressure Limit Control (Standard Pneumatic), Regulator Installation
  • 7.2.12 Pressure Limit Control (Tescom), Regulator Removal
  • 7.2.13 Pressure Limit Control (Tescom), Regulator Installation
  • 7.2.14 Panel Gauge Removal
  • 7.2.15 Panel Gauge Installation
  • 7.2.16 Test Port Quick-Connect Fitting (PN 59762) Removal and Installation - 3 and 100 Full Scale...
  • 7.2.17 Test Port Filter (PN 54188) Removal and Installation - 250 and 2500 Full Scale PSI
    • Removal
    • Installation
  • 7.2.18 Test Port Quick-Connect Fitting (PN 59004) and Filter (PN 54188) Removal and Installation ...
  • 7.2.19 Test Port (Output) Hose Quick-Connect Fitting and Filter Removal and Installation (PN 5699...
    • Removal
    • Installation
  • 7.2.20 Input Port Filter (PN 54188) Removal and Installation - 2500 Full Scale PSI
    • Input Port Filter Removal
    • Input Port Filter Installation
  • 7.2.21 AC Fuse (PN 58076) - Removal and Installation
  • 7.2.22 Input Port Filter (PN 54188) Removal and Installation - 5000 and 10000 Full Scale PSI
    • Removal
    • Installation
  • 7.2.23 AC Fuse (PN 58076) - Removal and Installation
  • 7.2.24 AC Power/EMI Line Filter (PN 58870) - Removal and Installation
  • 7.2.25 Power Switch (PN 58878) - Removal and Installation
    • Removal:
    • Installation:
      • 7.3 ORION-2C Valve Assembly Parts List
      • 7.4 ORION-3A Valve Assembly Parts List
• 8.0 Model Numbering System
• 9.0 Auto Selection Default Tables
  • Auto Selection (Gage) Default Table
  • Auto Selection (Absolute) Default Table
• 10.0 Conversion Factors
• 11.0 Options, Replacement Kits
• 12.0 Specifications
  • DLR3110 Warranty and Return Policy
  • DLR3110 Return Material Authorization Form