Document Outline

• SIDE BY SIDE Refrigerator
  • Table of Contents ..........2
  • www.crosley.com
  • 2211602 4/00
  • © 2000 All rights reserved. ® Registered Trademark of Crosley Printed in U.S.A.
    • Table of Contents
• Refrigerator Safety
  • ProperDisposalof YourOldRefrigerator
  • Installing Your Refrigerator
    • Unpacking Your Refrigerator
      • Removing packaging materials
      • Cleaning before use
    • Space Requirements
    • Electrical Requirements
      • Recommended grounding method
    • Base Grille
      • 1. Open both refrigerator doors.
        • 2. Place hands along the ends of the grille, with your thumbs along the top. Push in with your th...
      • 1. Open the doors.
        • 2. Line up the grille support tabs with the metal clips.
        • 3. Push the grille firmly to snap it into place.
    • Door Removal
  • TOOLS NEEDED: Z\v in. hex-head socket wrench, B\zn in. hex-head socket wrench and a flat-head scr...
  • IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect...
    • Handle Removal (optional)
      • 1. Apply firm pressure with your hand on the face of trim. Slide top trim up and bottom trim down...
        • 2. Remove handle screws and handles.
        • 3. Move refrigerator into place. Replace handles as shown (see Graphic1).
    • Door Removal
      • 1. Unplug refrigerator or disconnect power.
        • 2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corne...
        • 3. Close both doors and keep them closed until you are ready to lift them free from the cabinet.
        • 4. If you have a dispenser (ice or water), disconnect the water dispenser tubing located behind t...
        • 5. Remove top left hinge cover and screws as shown (see Graphic 4). DO NOT REMOVE SCREW 1.
        • 6. Disconnect wiring plug and both ground wires (see Graphic4).
        • 7. Carefully lift freezer door straight up off bottom hinge (see Graphic5). The water dispenser ...
        • 8. Remove top right hinge cover and screws as shown (see Graphic6). DO NOT REMOVE SCREW 1.
        • 9. Lift the refrigerator door straight up off bottom hinge.
        • 10. It may not be necessary to remove the bottom hinge to move the refrigerator through a doorway...
    • Door and Hinge Replacement
      • 1. Replace both bottom hinges, if removed. Tighten screws.
        • 2. Assistance may be needed to feed the water dispenser tubing through the bottom hinge while rei...
        • 3. Align and replace the top left hinge as shown (see Graphic4). Tighten screws.
        • 4. Reconnect both ground wires.
        • 5. Reconnect wiring plug.
        • 6. Replace left hinge cover and screws.
        • 7. Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.
        • 8. Align and replace the top right hinge as shown (see Graphic6). Tighten screws.
        • 9. Replace hinge cover and screws. Tighten screws.
        • 10. Plug into a grounded 3 prong outlet.
    • Door Closing
      • Door Closing
        • 1. Move the refrigerator into its final position.
          • 2. The two leveling screws are part of the front roller assemblies which are at the base of the r...
          • 3. Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise...
          • 4. Open both doors again and check to make sure that they close as easily as you like. If not, ti...
          • 5. Replace the base grille.
    • ConnectingtheRefrigerator toaWaterSource
      • Read all directions carefully before you begin.
      • IMPORTANT:
      • Cold water supply
        • 1. Unplug refrigerator or disconnect power.
          • 2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
          • 3. Locate a º in. to 1Z\v in. (12.7 mm to 3.18 cm) vertical COLD water pipe near the refrigerator.
          • 4. To determine the length of copper tubing you will need, measure from connection on lower left ...
          • 5. Using a grounded drill, drill a Z\v in. hole in the cold water pipe you have selected.
          • 6. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the...
          • 7. Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing in...
          • 8. Place the free end of the tubing into a container or sink, and turn ON main water supply and f...
        • 1. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten...
          • 2. Turn shut-off valve ON. Check for leaks. Tighten any connections (including connections at the...
          • 3. The ice maker is equipped with a built-in water strainer. If local water conditions require pe...
          • 4. Plug in refrigerator or reconnect power.
    • Water System Preparation
      • 1. Open the freezer door and turn off the ice maker. For Style 1 lift up the wire shut-off arm as...
        • 2. Install the interior water filter cartridge. The interior water filter mounting bracket is loc...
        • 3. Flush the water system by dispensing and discarding 2 to 3 gallons (8 to12 liters) or approxim...
        • 4. Inspect the filter system for water leaks. If you see water leaks, see the “Troubleshooting” s...
        • 5. Open the freezer door and turn on the ice maker. For Style 1 lower the wire shut-off arm. For ...
    • UnderstandingSoundsYouMayHear
    • Using Your Refrigerator
      • EnsuringProperAirCirculation
      • Setting the Controls
      • Adjusting Control Settings
      • Water and Ice Dispensers
        • (on some models)
          • The ice dispenser
            • 1. Press button for the desired type of ice.
              • 2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser op...
              • 3. Remove the glass to stop dispensing.
          • The water dispenser
            • 1. Press a glass against the water dispenser lever.
              • 2. Remove the glass to stop dispensing.
          • The dispenser light
          • The dispenser lock (on some models)
      • Interior Water Filtration System
        • (on some models)
          • Replacing the interior water filter cartridge
            • 1. Twist the interior water filter cartridge Z\v turn to the left. The INSTALL mark will be lined...
              • 2. Gently pull down on the cartridge to remove it from the filter mounting bracket assembly. To p...
              • 3. Install the new interior water filter cartridge. You can run the dispenser without a water fil...
              • 4. Line up the INSTALL mark on the water filter label with the indicator line that is molded into...
              • 5. Flush the water system by dispensing and discarding 2 to 3 gallons (8 to12 liters) or approxim...
              • 6. Inspect the filter system for water leaks. If you see water leaks, see the “Troubleshooting” s...
      • Ice Maker and Storage Bin/Bucket
        • (on some models - Accessory)
          • 1. To turn the ice maker on, simply lower the wire shut-off arm.
            • 2. To manually turn the ice maker off, lift the wire shut-off arm to the OFF (arm up) position an...
          • 1. Pull the covering panel out from the bottom and then slide it back toward the rear.
            • 2. Lift the wire shut-off arm so it clicks into the OFF (up) position. Ice can still be dispensed...
            • 3. Lift up the front of the storage bin and pull it out.
            • 4. Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shu...
          • 1. To turn the ice maker on, slide the control to the ON (left) position.
            • 2. To manually turn the ice maker off, slide the control to the OFF (right) position.
          • 1. Place four fingers in bucket base opening and rest thumb on the release button.
            • 2. Holding the base of the bucket with both hands, depress the release button and lift the bucket...
          • 1. Empty the ice container. Use warm water to melt the ice if necessary. Never use anything sharp...
            • 2. Wash ice bin or bucket with a mild detergent, rinse well and dry thoroughly. Do not use harsh ...
          • REMEMBER:
    • REfrigerator features
      • Refrigerator Shelves
        • Slide-out Shelves (on some models)
          • 1. Pull the shelf forward to the stop.
            • 2. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.
            • 3. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past...
        • Shelves and Shelf Frames
          • 1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.
            • 2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the fron...
            • 3. Lower the front of the shelf and check to make sure that the shelf is securely in position.
      • Lateral Adjustable Shelf
        • (on some models)
          • 1. Lift up on the front of shelf and slide to the desired location.
            • 2. Lower shelf to the level position.
          • 1. Hold the back of the shelf with one hand.
            • 2. Lift the front of the shelf with the other hand to a 45˚ angle and lower it slightly to releas...
          • 1. Remove the shelf track by lifting both sides of the track slightly and pulling the track strai...
            • 2. Replace the track by guiding the track hooks into the shelf support slots on the back wall.
            • 3. Push the track back and down securely into the shelf supports.
          • 1. Hold the shelf at the front and tip the front at a 45˚ angle to the track.
            • 2. Insert both of the rear shelf slides into the upper channel of the track, and lower the front ...
      • Flip-up Shelf
        • (on some models)
          • 1. To raise the shelf, pull forward on the lever located at the bottom front of the shelf and lif...
            • 2. To lower the shelf, lower the shelf until it is latched securely in place.
      • Adjustable Flip-up Shelf
        • (on some models)
          • 1. Raise the shelf by first sliding it back and down to make it half-width. (You can use the shel...
            • 2. Lift the front of the shelf until it fits securely in place against the back wall.
            • 3. Lower the shelf securely back into position.
            • 4. Pull the front of the shelf forward until it fits into place.
      • Deli Drawer
        • (on some models)
          • 1. Remove the deli drawer by sliding it straight out to the stop. Lift the front and slide the dr...
            • 2. Replace the deli drawer by sliding it back past the stop.
      • Convertible Vegetable/Meat Drawer, Crisper and Covers
        • (on some models)
          • 1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand ...
            • 2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.
          • 1. Remove the crisper and meat drawer. Press up in center of crisper glass insert until it rises ...
            • 2. Lift crisper cover frame up and remove. Repeat steps to remove the meat drawer cover.
            • 3. Replace back of meat drawer cover frame into supports on side walls of the refrigerator and lo...
            • 4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replac...
          • Meat storage guide
      • Convertible Vegetable/Meat Drawer Temperature Control
        • Adjusting the control
      • Crisper Humidity Control
        • (on some models)
      • Utility or Egg Bin
        • (on some models - Accessory)
      • Wine or Can/Bottle Rack
        • (on some models - Accessory)
          • 1. Remove the rack by pulling it straight out from the shelf.
            • 2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.
    • Freezer features
      • Freezer Shelf
        • (number of shelves varies with model)
          • 1. Lift the shelf off of the supports.
            • 2. Slide it out of the shelf support holes.
            • 3. Replace shelf in the reverse order.
          • Frozen food storage guide
      • Freezer Basket
        • (plastic bin on some models)
          • 1. Remove basket by sliding it out to the stop.
            • 2. Lift the front of the basket and slide it out the rest of the way.
            • 3. Replace the basket by positioning it on the side wall guide rails. Lift the basket front sligh...
    • Door features
      • Door Rails
        • Snap-on Door Rails
          • 1. Remove the rails by pushing in slightly on the front of the bracket while pulling out on the i...
            • 2. Replace the rails by aligning the ends of the brackets with the buttons on the sides of the do...
        • Drop-in Door Rails
          • 1. Remove the rails by pulling straight up on each end of the rail.
            • 2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail st...
      • Door Bins
        • (on some models)
          • 1. Remove the bin by lifting it up and pulling it straight out.
            • 2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.
      • Can Rack
        • (on some models - Accessory)
          • 1. Remove the rack by lifting it up and pulling straight out.
            • 2. Replace the rack by holding it above the desired support and pushing the rack back and down un...
    • Caring for Your Refrigerator
      • Cleaning Your Refrigerator
        • To clean your refrigerator:
          • 1. Unplug refrigerator or disconnect power.
            • 2. Remove all removable parts from inside, such as shelves, crispers, etc.
            • 3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge...
            • 4. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild ...
            • 5. Clean the condenser coils regularly. Coils may need to be cleaned as often as every other mont...
            • 6. Plug in refrigerator or reconnect power.
      • Changing the Light Bulbs
        • 1. Unplug refrigerator or disconnect power.
          • 2. Remove light shield when applicable as shown.
          • 3. Remove light bulb and replace with one of the same size, shape and wattage.
          • 4. Replace light shield when applicable as shown.
          • 5. Plug in refrigerator or reconnect power.
        • 1. Dispenser Light
      • Power Interruptions
        • 1. If the power will be out for 24 hours or less, keep both refrigerator doors closed to help foo...
          • 2. If the power will be out for more than 24 hours:
        • a) Remove all frozen food and store it in a frozen food locker.
        • OR
          • b) Place 2 lbs. (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. T...
        • OR
          • c) If neither a food locker nor dry ice is available, consume or can perishable food at once.
      • Vacation and Moving Care
        • Vacations
          • 1. Use up any perishables and freeze other items.
            • 2. If your refrigerator has an automatic ice maker:
            • 3. Empty the ice bin.
          • 1. Remove all food from the refrigerator.
            • 2. If your refrigerator has an automatic ice maker:
            • 3. Depending on your model, turn the Thermostat Control or Refrigerator Control to OFF. See the “...
            • 4. Clean refrigerator, wipe it, and dry well.
            • 5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to g...
        • Moving
          • 1. If your refrigerator has an automatic ice maker:
            • 2. Remove all food from the refrigerator and pack all frozen food in dry ice.
            • 3. Empty the ice bin.
            • 4. Depending on your model, turn the Thermostat Control or Refrigerator Control to OFF. See the “...
            • 5. Unplug the refrigerator.
            • 6. Empty water from the defrost pan.
            • 7. Clean, wipe, and dry thoroughly.
            • 8. Take out all removable parts, wrap them well, and tape them together so they don’t shift and r...
            • 9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw i...
            • 10. Tape the doors shut and the power cord to the refrigerator cabinet.
    • troubleshooting
      • Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
        • Your refrigerator will not operate
        • The lights do not work
        • There is water in the defrost drain pan
        • The motor seems to run too much
        • The refrigerator seems to make too much noise
        • The ice maker is not producing ice
        • The ice maker is producing too little ice
        • Off-taste, odor or grey color in the ice
        • The ice dispenser will not operate properly
        • The water dispenser will not operate properly
        • Water or ice is leaking from the dispenser
        • The dispenser water is not cool enough
        • The divider between the two compartments is warm
        • Temperature is too warm
        • There is interior moisture build-up
        • The doors will not close completely
        • The doors are difficult to open
        • Water flow from the dispenser decreases noticeably
    • AssistanceorService
      • If you need replacement parts
      • In the U.S.A.
        • For further assistance
      • Accessories
        • Replacement filters
        • Interior water filter cartridge:
    • Water filter certifications
• Product Data Sheets
  • Standard Interior Water Filtration System Model WFI-NL200/NL200
  • Cyst Interior Water Filtration System Model WFI-NLC200/NLC200
    • Application Guidelines/Water Supply Parameters
    • City or Well 30 - 120 psi (207 - 827 kPa) 33˚ - 100˚F (0.6˚ - 37.8˚ C)
• CROSLEY® Refrigerator Warranty