Document Outline

• PCM-3370 Manual
• Contents
• Chapter 1 General Information
  • 1.1 Introduction
  • 1.2 Features
  • 1.3 Specifications
  • 1.4 Board Dimensions
    • Figure 1.1: Board Dimensions (Component Side)
    • Figure 1.2: Board Dimensions (Solder Side)
• Chapter 2 Installation
  • 2.1 Jumpers
    • Table 2.1: connectors and jumpers
  • 2.2 Locating jumpers and connectors
    • Figure 2.1: Locating Connectors and Jumpers
    • Figure 2.2: Locating Connectors (Solder Side)
  • 2.3 Setting Jumpers
  • 2.4 CPU
    • 2.4.1 CMOS clear (JP1)
    • 2.4.2 PCI VIO Select (JP3)
      • Table 2.3: PCI VIO Select (JP3)
    • 2.4.3 COM1 and COM2 RI Input Select (JP4, JP5)
      • Table 2.4: COM1 and COM2 RI Input Select (JP4, JP5)
      • Table 2.5: COM1 and COM2 RI Input Select (JP4, JP5)
  • 2.5 SDRAM installation
    • 2.5.1 SODIMM DRAM
  • 2.6 Primary (2.5") IDE connector (CN12)
    • 2.6.1 Connecting the hard drive
  • 2.7 LPT1 (primary parallel port) connector (CN14)
  • 2.8 Keyboard/mouse connectors (CN17)
  • 2.9 Power connectors (CN15, CN18)
    • 2.9.1 Main power connector (CN15)
    • 2.9.2 ATX standby power input connector (CN18)
  • 2.10 Serial (COM1,COM2) (CN13,CN16)
    • 2.10.1 Primary(COM1:CN20/CN21,COM2:CN14/CN16)
  • 2.11 COM2 422/485 (CN6)
  • 2.12 VGA interface connections
    • 2.12.1 CRT display connector (CN8)
    • 2.12.2 Flat panel display connector (CN7,CN20)
    • 2.12.3 Invert Power Connector (CN2)
  • 2.13 Ethernet configuration
    • 2.13.1 Ethernet connector (CN5)
    • 2.13.2 Network boot
  • 2.14 Watchdog timer configuration
    • 2.14.1 Watchdog timer action (JP2)
      • Table 2.6: Watchdog Function J2
  • 2.15 USB connector (CN26,CN27)
  • 2.16 Reset Connector (CN1)
    • Table 2.7: Reset Connector
  • 2.17 IR Connector (CN3)
  • 2.18 FAN Connector (CN4)
    • 2.18.1 Power Switch Connector (CN19)
    • 2.18.2 Negative Power Input
    • 2.18.3 RTC Connector (CN22)
• Chapter 3 Software Configuration
  • 3.1 Introduction
  • 3.2 VGA display firmware configuration
    • Figure 3.1: VGA setup screen
  • 3.3 Connections for four standard LCDs
    • Table 3.1: Sharp LM64183P LCD (CN35)
  • 3.4 Ethernet software configuration
• Chapter 4 Award BIOS Setup
  • 4.1 System test and initialization
    • 4.1.1 System configuration verification
  • 4.2 Award BIOS setup
    • 4.2.1 Entering setup
      • Figure 4.1: Setup Program Initial Screen
    • 4.2.2 Standard CMOS setup
      • Figure 4.2: CMOS Setup Screen
    • 4.2.3 BIOS features setup
      • Figure 4.3: BIOS Features Setup Screen
    • 4.2.4 Chipset features setup
      • Figure 4.4: ChipsetFeatures Setup Screen
    • 4.2.5 Power management setup
      • Figure 4.5: Power Management Setup Screen
    • 4.2.6 PnP/PCI configuration setup
      • Figure 4.6: PCI configuration setup screen
    • 4.2.7 Integrated peripherals
      • Figure 4.7: Integrated peripherals setup screen
    • 4.2.8 Load Optimized Defaults BIOS
      • Figure 4.8: Load Optimized Default BIOS screen
    • 4.2.9 Set Password
    • 4.2.10 Save & exit setup
      • Figure 4.9: Save and Exit Setup Screen
    • 4.2.11 Quit without saving
      • Figure 4.10: Quit Setup Screen
• Chapter 5 AGP 4X Setup
  • 5.1 Introduction
    • 5.1.1 Chipset
    • 5.1.2 Display memory
    • 5.1.3 Display types
    • 5.1.4 Dual/Simultaneous Display
      • Figure 5.1: Selecting Display Settings
  • 5.2 Installation of the SVGA Driver
    • 5.2.1 Installation for Windows 95
    • 5.2.2 Installation for Windows 98/Me
    • 5.2.3 Installation for Windows NT
    • 5.2.4 Installation for Windows 2000
    • 5.2.5 Installation for Windows XP
  • 5.3 Further Information
• Chapter 6 PCI Bus Ethernet Interface
  • 6.1 Introduction
  • 6.2 Installation of Ethernet Driver
    • 6.2.1 Installation for MS-DOS and Windows 3.1
    • 6.2.2 Installation for Windows 95
    • 6.2.3 Installation for Windows 2000
    • 6.2.4 Installation for Windows NT
  • 6.3 Further information
• Appendix A Programming the Watchdog Timer
  • A.1 Programming the watchdog timer
• Appendix B PCM-3370F Jumper Settings
  • B.1 CN1 Reset Connector
  • B.2 CN2 Inverter Power Connector
  • B.3 CN3 IR Connector
  • B.4 CN4 FAN Connector
  • B.5 CN5 LAN Connector
  • B.6 CN6 422/485 Connector
  • B.7 CN7 40-Pin LCD Port (24bit)
  • B.8 CN8 CRT Connector
  • B.9 CN9 USB Connector
  • B.10 CN10 20-Pin LCD Connector (36-bit)
  • B.11 CN11 PC/104+ Connector
  • B.12 CN12 44-Pin IDE Connector
  • B.13 CN13 COM2 RS232 Connector
  • B.14 CN14 LPT Connector
  • B.15 CN15 Power Conector
  • B.16 CN16 COM1 RS232 Connector
  • B.17 CN17 KB/MS Connector
  • B.18 CN18 ATX Power Connector
  • B.19 CN19 Power Switch Connector
  • B.20 CN20 Negative Power Input
  • B.21 CN21 Compact Flash Slot
  • B.22 CN22 RTC Connector
  • B.23 JP1 COMS Charge&Discharge
  • B.24 JP2 Watchdog Timer
  • B.25 JP3 PCI VIO Select
  • B.26 JP4 COM1 RI Input Select
  • B.27 JP5 COM2 RI Input Select
• Appendix C System Assignments
  • C.1 System I/O ports
  • C.2 DMA channel assignments
  • C.3 Interrupt assignments
  • C.4 1st MB memory map